Front Passenger Side Seat Belt Warning Light does not Operate [01/2019 - 09/2022]: Procedure
- CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)
- Clear the DTCs.
Body Electrical > Occupant Detection > Clear DTCs
- Check for DTCs.
Body Electrical > Occupant Detection > Trouble Codes
Result
Result Proceed to DTCs are not output A DTCs are output B
Result:
B
GO TO OCCUPANT CLASSIFICATION SYSTEM. Refer to DIAGNOSIS SYSTEM [01/2019 - 09/2022]
Result:
A
See step 2
- Clear the DTCs.
- CHECK DTC OUTPUT (AIRBAG SYSTEM)
- Clear the DTCs.
Body Electrical > SRS Airbag > Clear DTCs
- Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
Result
Result Proceed to DTCs are not output A DTCs are output B
Result:
B
GO TO AIRBAG SYSTEM. Refer to DIAGNOSTIC TROUBLE CODE CHART [01/2019 - 04/2020] , or refer to DIAGNOSTIC TROUBLE CODE CHART [04/2020 - 06/2021] , or refer to DIAGNOSTIC TROUBLE CODE CHART [06/2021 - 09/2022]
Result:
A
See step 3
- Clear the DTCs.
- READ VALUE USING TECHSTREAM
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / Occupant Detection / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > Occupant Detection > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Passenger Buckle SW Front passenger buckle switch Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined- Body Electrical > Occupant Detection > Data List
Tester Display Passenger Buckle SW Result
Result Proceed to Unset or Set is displayed on the Techstream according to the front passenger seat belt condition A Unset or Set is not displayed correctly on the Techstream according to the front passenger seat belt condition B NG is displayed on the Techstream C
Result:
B
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH. Refer to REMOVAL [01/2019 - 03/2019] , or refer to REMOVAL [03/2019 - 09/2022]
Result:
C
REPLACE OCCUPANT DETECTION ECU. Refer to REMOVAL [01/2019 - 03/2019] , or refer to REMOVAL [03/2019 - 09/2022]
Result:
A
See step 4
- READ VALUE USING TECHSTREAM
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Body Electrical / SRS Airbag / Data List.
- Read the Data List according to the display on the Techstream.
Body Electrical > SRS Airbag > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note Right side Buckle SW RH buckle switch Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined- Body Electrical > SRS Airbag > Data List
Tester Display Right side Buckle SW Result
Result Proceed to Unset or Set is displayed on the Techstream according to the front passenger seat belt condition A - Unset or Set is not displayed correctly on the Techstream according to the front passenger seat belt condition
- NG is displayed on the Techstream
B
Result:
A
USE SIMULATION METHOD TO CHECK. Refer to HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ]
Result:
B
REPLACE AIR BAG SENSOR ASSEMBLY. Refer to REMOVAL [01/2019 - 03/2019] , or refer to REMOVAL [03/2019 - 09/2022]