LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 219 (Lighting System (Except HEV) (W/O AFS) - Symptom Tests & Circuit Tests (2 Of 2)) >> LIGHTING SYSTEM (for Gasoline Model without AFS) >> High Beam Headlight Circuit [01/2019 - 09/2022] >> Procedure

High Beam Headlight Circuit [01/2019 - 09/2022]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, 2020 Toyota Corolla, and 2019 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. PERFORM ACTIVE TEST USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Active Test.
    5. Perform the Active Test according to the display on the Techstream.

      Body Electrical > Main Body > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Head Light Hi High beam headlights OFF or ON -

      Body Electrical > Main Body > Active Test 

      Tester Display
      Head Light Hi

      OK

      High beam headlights illuminate.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [01/2019 - 03/2019]  , or refer to  PROBLEM SYMPTOMS TABLE [03/2019 - 09/2019]  , or refer to  PROBLEM SYMPTOMS TABLE [09/2019 - 04/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [04/2020 - 09/2022] 

    Result: 

    NG 

    See step  2

  2. INSPECT NO. 1 INTEGRATION RELAY 
    1. Remove the No. 1 integration relay.

      Refer to REMOVAL [01/2019 - 03/2019] , or refer to REMOVAL [03/2019 - 09/2022]

    2. Inspect the No. 1 integration relay.

      Refer to INSPECTION [01/2019 - 09/2022]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE NO. 1 INTEGRATION RELAY. Refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (POWER SOURCE - NO. 1 INTEGRATION RELAY) 
    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      1B-9 - Body ground Always 11 to 14 V
      1B-11 - Body ground Always 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) 
    1. Disconnect the I85 main body ECU (multiplex network body ECU) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1B-12 - I85-13 (DIM) Always Below 1 Ω
      1B-12 or I85-13 (DIM) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU). Refer to  REMOVAL [01/2019 - 03/2019]  , or refer to  REMOVAL [03/2019 - 09/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals