LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 116 (Navigation System (2019-Early 2023) - Diagnostic Codes (1 Of 2)) >> Navigation System >> DTC B1324: Lost Communication with Meter [09/2022 - 11/2022] >> Procedure

DTC B1324: Lost Communication with Meter [09/2022 - 11/2022]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 Toyota GR Corolla, 2023 Toyota Corolla, 2022 Toyota Corolla, 2021 Toyota Corolla, and 2020 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DTC 
    1. Check for DTCs and check that no DTCs are output.

      Body Electrical > Navigation System > Trouble Codes 

      Result

      Result Proceed to
      DTC B1324 is not output A
      DTC B1324 is output B

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [06/2018 - ] 

    Result: 

    B 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE) 
    1. Disconnect the I4 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I4-23 (ES) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      I4-22 (B) - Body ground Always 11 to 14 V
      I4-38 (IG+) - Body ground Ignition switch to ON 11 to 14 V

      Result

      Result Proceed to
      OK (w/ Headup Display System) A
      OK (w/o Headup Display System) B
      NG C

    Result: 

    B 

    See step  7

    Result: 

    C 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    A 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the I108 No. 2 junction connector.
    3. Connect the I4 combination meter assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I108-3 - I108-14 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  6

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the I108 No. 2 junction connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I108-1 - I108-12 Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE NO. 2 JUNCTION CONNECTOR 

    Result: 

    NG 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 2 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the I56 radio and display receiver assembly connector.
    3. Connect the I108 No. 2 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-5 (CNH1) - I56-6 (CNL1) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2022 - 11/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR) 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the I4 combination meter assembly connector.
    3. Connect the I108 No. 2 junction connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I4-27 (MSCH) - I4-10 (MSCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2022 - 11/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  7. CHECK HARNESS AND CONNECTOR 
    1. Disconnect the cable from the negative (-) battery terminal.
    2. Disconnect the I4 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I4-27 (MSCH) - I4-10 (MSCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [09/2022 - 11/2022] 

    Result: 

    NG 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the I56 radio and display receiver assembly connector.
    2. Disconnect the I4 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I56-5 (CNH1) - I4-27 (MSCH) Always Below 1 Ω
      I56-6 (CNL1) - I4-10 (MSCL) Always Below 1 Ω
      I56-5 (CNH1) or I4-27 (MSCH) - Body ground Always 10 kΩ or higher
      I56-6 (CNL1) or I4-10 (MSCL) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [09/2022 - 11/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals