LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2023 >> RAV4 XLE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 5 (Power Back Door System (HV) - Diagnostics - Introduction) >> POWER BACK DOOR SYSTEM (for HV Model) >> Data List / Active Test [11/2018 - 10/2023] >> Data List / Active Test [11/2018 - 10/2023]

Data List / Active Test [11/2018 - 10/2023]

WARNING: This page is about a different variant/trim than selected.
  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Turn the power switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the power switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Back Door, Main Body or Smart Key / Data List.
    6. According to the display on the Techstream, read the Data List.

      Body Electrical > Back Door > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Door Lock Status Back door condition signal Lock or Unlock Lock: Back door locked
      Unlock: Back door unlocked      		 -
      Half Latch SW Latch switch signal ON or OFF ON: Back door lock motor open-latched
      OFF: Back door lock motor full-latched or half-latched      		 -
      Closer Position SW Initial switch signal ON or OFF ON: Back door lock sector gear in center position (Initial switch on)
      OFF: Back door lock sector gear out of center position (Initial switch off)      		 -
      Pawl Position Switch Pawl switch signal ON or OFF ON: Back door lock motor open-latched
      OFF: Back door lock motor except open-latched      		 -
      Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
      OFF: Back door closed      		 -
      PBD Touch Sensor (Right) Power back door sensor assembly RH signal ON, OFF or Open ON: Power back door sensor assembly RH pressed
      OFF: Power back door sensor assembly RH not pressed
      Open: Power back door sensor assembly RH circuit open      		 -
      PBD Touch Sensor (Left) Power back door sensor assembly LH signal ON, OFF or Open ON: Power back door sensor assembly LH pressed
      OFF: Power back door sensor assembly LH not pressed
      Open: Power back door sensor assembly LH circuit open      		 -
      PBD Main SW Power back door ON/OFF signal ON or OFF Current customize setting displayed -
      PBD Close SW No. 1 power back door control switch signal ON or OFF ON: No. 1 power back door control switch pushed
      OFF: No. 1 power back door control switch not pushed      		 -
      IG SW Power switch signal ON or OFF ON: Power switch on (IG)
      OFF: Power switch off      		 "OFF" is also displayed for this item when the power switch is on (ACC).
      Door Lock Signal Back door condition signal Lock or Unlock Lock: Back door locked
      Unlock: Back door unlocked      		 -
      PBD Position (3/4-Open) Load signal detected during back door closing operation (3/4 - Open) Caution or OK Caution: Load detected between back door 3/4 and fully open position during back door closing operation
      OK: No load detected between back door 3/4 and fully open position during back door closing operation      		 -
      PBD Position (2/4-3/4) Load signal detected during back door closing operation (2/4 - 3/4) Caution or OK Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation
      OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation      		 -
      PBD Position (1/4-2/4) Load signal detected during back door closing operation (1/4 - 2/4) Caution or OK Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation
      OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation      		 -
      PBD Position (Close-1/4) Load signal detected during back door closing operation (Close - 1/4) Caution or OK Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation
      OK: No load detected between back door fully closed and 1/4 open position during back door closing operation      		 -
      Closed Position Initialization Back door fully closed position memorized signal Not Initialized or Initialized Not Initialized: Back door fully closed position not memorized
      Initialized: Back door fully closed position memorized      		 -
      PBD SW Operation Power back door switch operation ON or 0.8 s Current customize setting displayed -
      PBD Buzz In Use Power back door warning buzzer operation condition signal ON or OFF Current customize setting displayed -
      PBD Assist Open Operation Function that enables or disables the power back door assist open operation. When PBD Assist Open Operation is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. OFF or ON Current customize setting displayed -
      PBD Assist Close Operation Function that automatically fully closes the back door when a stopped back door is moved by hand in the closing direction. OFF or ON Current customize setting displayed -
      Door Unlock with 1 Motion. Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly). BackDoor or ALL DOORS Current customize setting displayed -
      Wireless Power Back Door Open Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock:0.8s Current customize setting displayed -
      Power Back Door Opening Adjust Function that can be used to set the power back door opening angle at 6 different positions. User Setting Position, Min, Small, Middle, Large or Max Current customize setting displayed -
      Emblem Sensor Rear emblem sensor assembly connection status.*1 Without or With Without: Rear emblem sensor assembly not connected
      With: Rear emblem sensor assembly connected      		 Not applicable
      Emblem Sensor Detection Rear emblem sensor assembly detection status.*1 OFF or ON OFF: Rear emblem sensor assembly not detecting a hand
      ON: Rear emblem sensor assembly detecting a hand      		 Not applicable
      PBD/Emblem Sensor Function Function that enables/disables the power back door and rear emblem sensor assembly.*1 PBD OFF/Emblem OFF, PBD ON/Emblem OFF or PBD ON/Emblem ON Current customize setting displayed Not applicable
      PBD Buzzer Volume Adjust Function that changes the power back door buzzer setting. Small, Middle of Large Current customize setting displayed -
      Emblem Sensor Detection Sensitivity Function that changes the sensitivity of the rear emblem sensor assembly.*1 Low, Middle or High Current customize setting displayed Not applicable
      Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Frequent Contact/Calibration Failure) Number of times emblem sensor changed to sensitivity reduction mode (frequent contact/calibration failure)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Power Saving) Number of times emblem sensor changed to sensitivity reduction mode (power saving)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Emblem Sensor Sensitivity Drop Frequency (Disturbance Factor) Number of times emblem sensor sensitivity decreased (wave interference)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Emblem Sensor Sensitivity Drop Frequency (Foreign Matter Adhering) Number of times emblem sensor sensitivity decreased (adherence of foreign matter)*1 None, Low, Middle or High None: Never
      Low: 1 to 10 times
      Middle: 11 to 50 times
      High: 51 times or more      		 Not applicable
      Kick Sensor Connection Status of the kick door control sensor connection*2 Without or With Without: kick door control sensor not equipped
      With: kick door control sensor equipped      		 -
      Kick Sensor Detection Status of the kick door control sensor detection*2 OFF or ON OFF: Kick door control sensor not detecting a foot
      ON: Kick door control sensor detecting a foot      		 -
      Kick Sensor Error Status of the kick door control sensor error*2 Normal or Error Normal: Kick door control sensor is normal
      Error: Kick door control sensor is abnormal      		 -
      Kick Sensor Function Status of the hands free power back door function*2 OFF or ON Current customize setting displayed -
      #Codes Number of DTCs Min.: 0, Max.: 255 Number of DTCs will be displayed -
      1. *1: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
      2. *2: w/ Hands Free Power Back Door

      Body Electrical > Main Body > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Back Door Courtesy SW Back door courtesy switch signal ON or OFF ON: Back door open
      OFF: Back door closed      		 -
      Back Door Open Back door condition signal Permit or Prohibit Permit: Back door unlocked
      Prohibit: Back door locked      		 -
      Back Door Open SW Power back door switch assembly signal ON or OFF ON: Power back door switch assembly on
      OFF: Power back door switch assembly off      		 -
      Back Door Open Handle SW Back door opener switch assembly (open switch) signal ON or OFF ON: Back door opener switch assembly (open switch) on
      OFF: Back door opener switch assembly (open switch) off      		 -
      Kick Sensor Operation with ACC ON Status of the hands free power back door function with power switch on (ACC)* Not Available or Available Current customize setting displayed -
      1. *: w/ Hands Free Power Back Door

      Body Electrical > Smart Key > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Tr/B-Door Unlock SW Back door opener switch assembly (open switch) signal ON or OFF ON: Back door opener switch assembly (open switch) on
      OFF: Back door opener switch assembly (open switch) off      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Turn the power switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the power switch on (IG).
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Back Door / Active Test.
    6. According to the display on Techstream perform the "Active Test".

      Body Electrical > Back Door > Active Test 

      Tester Display Measurement Item Control Range Diagnostic Note
      Latch Release Latch release operation ON or OFF -
      PBD Open/Close Power back door motor operation OFF, Open or Close -
      PBD Buzzer Power back door warning buzzer sound OFF or ON -
scientia non olet · About LEMON Manuals