LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2023 >> RAV4 XLE, FWD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Safety Connect System - Diagnostic Codes (2 Of 2), Circuit Tests & Symptom Tests >> Safety Connect System >> Green Indicator Remains Off [11/2018 - 10/2019] >> Procedure

Green Indicator Remains Off [11/2018 - 10/2019]: Procedure

  1. CONFIRM GREEN INDICATOR COMES ON 
    1. After the ignition switch is turned to ON and the manual (SOS) switch red indicator has come on for 2 seconds, confirm that the manual (SOS) switch green indicator comes on for 2 seconds.

      OK

      Green indicator comes on.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  6

    Result: 

    OK 

    See step  2

  2. CONFIRM SUBSCRIPTION MODE 
    1. Confirm the indicator status 5 seconds after the ignition switch is turned to ON.

      Result

      Result Proceed to
      Green indicator remains on A
      Green indicator remains off B
      Red and green indicators both flash (1 second intervals, for 20 seconds) C

      HINT: 

      If red and green indicators are flashing, the system is in shipping mode, so the system should be changed to either active mode or deactive mode.

    Result: 

    CHECK FOR INTERMITTENT PROBLEMS. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ] 

    Result: 

    CHANGE SUBSCRIPTION MODE 

    Result: 

    See step  3

  3. INPUT VIN WITH TECHSTREAM 
    1. Turn the ignition switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON and wait for 10 seconds.
    4. Turn the Techstream on.
    5. Select "Vehicle Inquiry" and input the VIN.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  4

  4. CONFIRM SUBSCRIPTION MODE 
    1. Confirm the indicator status at 5 seconds after the ignition switch is turned to ON.

      Result

      Result Proceed to
      Green indicator remains on A
      Green indicator remains off B

    Result: 

    END 

    Result: 

    See step  5

  5. REPLACE DCM (TELEPHONE TRANSCEIVER ASSEMBLY) 
    1. Replace the DCM (Telephone Transceiver Assembly).

      Refer to REMOVAL [11/2018 - 10/2019]

      NOTE:
      • The ignition switch must be off.
      • Do not exchange the DCM (Telephone Transceiver Assembly) with one from another vehicle.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    PERFORM DCM ACTIVATION. Refer to  DCM ACTIVATION [11/2018 - 10/2019] 

  6. CHECK DTC 
    1. Turn the ignition switch off.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON and wait for 10 seconds.
    4. Turn the Techstream on.
    5. Perform "Health Check" and check for current DTCs.

      Refer to HEALTH CHECK [11/2018 - 10/2019]

      Result

      Result Proceed to
      DTCs are not output A
      DTCs are output B

    Result: 

    GO TO DIAGNOSTIC TROUBLE CODE CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [11/2018 - 10/2019] 

    Result: 

    See step  7

  7. REPLACE DCM (TELEPHONE TRANSCEIVER ASSEMBLY) 
    1. Replace the DCM (Telephone Transceiver Assembly).

      Refer to REMOVAL [11/2018 - 10/2019]

      NOTE:
      • The ignition switch must be off.
      • Do not exchange the DCM (Telephone Transceiver Assembly) with one from another vehicle.

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    PERFORM DCM ACTIVATION. Refer to  DCM ACTIVATION [11/2018 - 10/2019]