Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door window frame moulding removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Power window regulator motor assembly LH Power window regulator motor assembly RH Rear door window regulator sub-assembly LH* Rear door window regulator sub-assembly RH* Rear door glass sub-assembly LH* Rear door glass sub-assembly RH* Rear door glass run LH* Rear door glass run RH*	Initialize power window control system	Auto up and down function Remote control function Key-off operation function Wireless transmitter-linked function Key-linked function Window open warning function Catch protection function Jam protection function	Refer to REGISTRATION [12/2022 - ]

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

NOTE:

After the ignition switch is turned off, the radio and display receiver assembly recordsvarious types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative(-) auxiliary battery terminal.
Refer to BEFORE DISCONNECTING BATTERY [12/2022 - ]
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled uponnext startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
Refer to INSPECTION MODE PROCEDURE [12/2022 - ]

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

LEARNING COMPLETES WHEN VEHICLE IS DRIVEN

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.	Refer to INITIALIZATION [12/2022 - ]

LEARNING COMPLETES WHEN VEHICLE IS OPERATED NORMALLY

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power Door Lock Control System*1 Back door opener	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.	Refer to INITIALIZATION [12/2022 - ]
Power Back Door System*2	Reset back door close position	Refer to INITIALIZATION [12/2022 - ]
Air Conditioning System	for HEV Model: After the ignition switch is turned to ON, the servo motor standard position is recognized. for PHEV Model: After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.	-

Effect/Inoperative Function When Necessary Procedures are not Performed

Necessary Procedures

Link

Power Door Lock Control System*1

Back door opener

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Refer to INITIALIZATION [12/2022 - ]

Power Back Door System*2

Reset back door close position

Refer to INITIALIZATION [12/2022 - ]

Air Conditioning System

for HEV Model:

After the ignition switch is turned to ON, the servo motor standard position is recognized.

for PHEV Model:

After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.

*1: w/o Power Back Door System*2: w/ Power Back Door System

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

COMPONENTS (REMOVAL)

Fig 1: Rear Door Window Frame Moulding Removal Components [03/2023 - ]

Callout - Procedure		Part Name Code
1	REAR DOOR OUTSIDE HANDLE ASSEMBLY	69240	-	-	-
2	REAR DOOR CHECK ASSEMBLY	68630	-	-	-
3	REAR DOOR WEATHERSTRIP	67872	See step 3	-	-
4	REAR DOOR WINDOW FRAME FRONT MOULDING	75762A	See step 4	-	-
5	REAR DOOR WINDOW FRAME UPPER MOULDING	75764A	See step 5	-	-

•

Non-reusable part