Caution / Notice / Hint

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure		Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Battery terminal is disconnected/reconnected		Turn the ignition switch to ON, wait for 10 seconds or more, and start the engine.	The electronic throttle system will initialized	-
		Let the engine run at idle until it fully warms up (the radiator fan turns 2 times or more) under no electrical load condition. After connecting the ground terminal to the battery sensor, wait for 10 seconds or more and turn the ignition switch to ON.	The engine control system will initialized	-
		Set the clock to the current time.	The clock on the meter display will initialized	-
		Set to the contents checked before disconnecting the battery.	The EyeSight system will initialized	-
		Audio (settings that the customer set): Set to the contents checked before disconnecting the battery. Navigation system (settings that the customer set): Time setting is not necessary because the time information is received via GPS. Navigation system (settings that the customer set): Set the sound and other settings (items that were set in the selection) to the contents checked before disconnecting the battery.	The audio and visual system will initialized	-
		Perform the Bluetooth connection procedure between head unit (without navigation) and smartphone.	The telematics system will initialized	-
Read Control module setting information		Read the setting information from the combination meter before replacement, and save it to the GTS.	-	See step 1
Write Control module setting information	Write saved setting information data*1	Write the setting information saved by "Read Control module setting information" to the new combination meter.	-	See step 13
Write Control module setting information	Write applied models and option codes*2	Using applied models and option codes, write the setting information to the new combination meter.	-	See step 13

*1: When the combination meter can communicate with the GTS before replacement ("Read Control module setting information" is possible).

*2: When the combination meter cannot communicate with the GTS before replacement ("Read Control module setting information" is not possible).

NOTE:

Refer to "PRECAUTION" before handling the airbag system components.

Refer to PRECAUTION [11/2021 - ]

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

LEARNING COMPLETES WHEN VEHICLE IS OPERATED NORMALLY

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Keyless Access System with Push Button Start Push Button Start Function	Open and close the driver door Engine start operation	Refer to INITIALIZATION [11/2021 - ]

COMPONENTS (REMOVAL)

Fig 1: Combination Meter Removal Components

Procedure		Part Name Code
1	READ CONTROL MODULE SETTING INFORMATION	-	See step 1	-	-
2	NEGATIVE BATTERY TERMINAL	-	-	-	-
3	STEERING WHEEL POSITION	-	-	-	-
4	CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL	55413C	See step 4	-	-
5	INSTRUMENT SIDE PANEL LH	55318C	See step 5	-	-
6	INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY	55403F	See step 6	-	-
7	INSTRUMENT SIDE PANEL RH	55317A	See step 7	-	-
8	INSTRUMENT PANEL ORNAMENT	55461A	-	-	-
9	INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY	55404D	-	-	-
10	METER HOOD SUB-ASSEMBLY	55403	-	-	-
11	CENTER INSTRUMENT PANEL REGISTER ASSEMBLY	55670A	See step 11	-	-
12	NO. 2 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY	55062	See step 12	-	-
13	UPPER INSTRUMENT PANEL METER ORNAMENT	55422	-	-	-
14	COMBINATION METER ASSEMBLY	83100	See step 14	-	-