LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> RAV4 LE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 64 (Automatic Transaxle System (UB80F) - Service Information (1 Of 3)) >> Transmission Wire >> Removal [11/2018 - 10/2019] >> Procedure

Removal [11/2018 - 10/2019]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 8

  2. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 9

  3. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10

  4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11

  5. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 12

  6. DRAIN AUTOMATIC TRANSAXLE FLUID 
    1. Remove the refill plug and gasket from the automatic transaxle case sub-assembly.
      GTY929356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.
      GTY929423Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.
      GTY870794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 1 Transmission Oil Filler Tube
    4. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

      Torque: 1.7 N.m (17 kgf/cm, 15 in.lbf) 

    5. Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

      HINT: 

      Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

    6. Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

      HINT: 

      Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

  7. REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System) 

    Refer to REMOVAL [11/2018 - ]

  8. REMOVE FRONT ENGINE MOUNTING INSULATOR 

    Refer to PROCEDURE - Step 6

  9. SEPARATE OIL COOLER UNION SUB-ASSEMBLY 
    1. Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.
      GTY854856Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Oil Cooler Union Bolt
    2. Remove the oil cooler union bolt and 2 gaskets to separate the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.
  10. REMOVE TRANSMISSION CASE SIDE COVER 
    1. Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.
      GTY895621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for AW (AISIN AW) Made
      *B for AWNC (AISIN AW) Made
  11. REMOVE TRANSMISSION WIRE (w/o Stop And Start System) 
    1. Disengage the claw, rotate the lever and disconnect the transmission wire connector.
      GTY744261Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.
      GTY740207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Connector (A)
      *b Connector (B)
    3. Disconnect the 9 solenoid valve connectors.

      HINT: 

      • Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
      • Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.
    4. Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.
      GTY732594Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.
      GTY740932Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.
      GTY694193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE TRANSMISSION WIRE (w/ Stop And Start System) 
    1. Disengage the claw, rotate the lever and disconnect the transmission wire connector.
      GTY744261Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.
      GTY896994Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Connector (A)
      *b Connector (B)
    3. Disconnect the 9 solenoid valve connectors.

      HINT: 

      • Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
      • Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.
    4. Disengage the wire harness clamp to disconnect the transmission wire (oil pump with solenoid assembly).
      GTY718010Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the transmission wire connector.
      GTY718000Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disengage the clamp to disconnect the transmission wire (oil pump with solenoid assembly) from the solenoid lock plate.
      GTY718002Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.
      GTY732594Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.
      GTY740932Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.
      GTY694193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals