Jam Protection Function Activates During Power Back Door Operation [11/2018 - 10/2023]: Procedure

1. Check if there are any foreign objects interfering with back door operation.

   Result

   Result	Proceed to
   There are no foreign objects	A
   There are foreign objects	B

Result: 

B 

REMOVE FOREIGN OBJECT 

Result: 

A 

See step  2

1. Check back door operation.
   1. Turn the main switch so that it is not pushed.

      Refer to CUSTOMIZE PARAMETERS [11/2018 - 10/2023]

      NOTE:

      This check is possible only when the "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "Off" (The default setting is "On").

   2. Open/close the back door by hand.

   Result

   Result	Proceed to
   The back door fully opens and closes smoothly	A
   The back door does not fully open and close smoothly	B

2. Check main switch condition.
   NOTE:

   The "System Settings" customization setting using the multi-information display in the combination meter assembly is set to "On" (The default setting is "On").

   1. Turn the main switch so that it is pushed.

      Refer to CUSTOMIZE PARAMETERS [11/2018 - 10/2023]

Result: 

B 

ADJUST BACK DOOR 

Result: 

A 

See step  3

1. Check the Data List to determine if the power back door sensor assembly functions properly.

   Refer to DATA LIST / ACTIVE TEST [11/2018 - 10/2023]

   Body Electrical > Back Door > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   PBD Touch Sensor (Right)	Power back door sensor assembly RH signal	ON, OFF or Open	ON: Power back door sensor assembly RH pressed OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open	-
   PBD Touch Sensor (Left)	Power back door sensor assembly LH signal	ON, OFF or Open	ON: Power back door sensor assembly LH pressed OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open	-

   Body Electrical > Back Door > Data List 

   Tester Display
   PBD Touch Sensor (Right)
   PBD Touch Sensor (Left)

   Result

   Result	Proceed to
   On the Techstream screen, ON or OFF is displayed accordingly	A
   On the Techstream screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly RH	B
   On the Techstream screen, ON or OFF is not displayed accordingly or Open is displayed for power back door sensor assembly LH	C

Result: 

B 

See step  6

Result: 

C 

See step  8

Result: 

A 

See step  4

1. Temporarily replace the power back door unit assembly set with a new or normally functioning one.

   Refer to REMOVAL [11/2018 - 10/2023]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  5

1. Check power back door system operation.

   Refer to OPERATION CHECK [11/2018 - 10/2023]

   OK

   Power back door system operates normally.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (POWER BACK DOOR UNIT ASSEMBLY SET WAS DEFECTIVE) 

Result: 

NG 

REPLACE MULTIPLEX NETWORK DOOR ECU. Refer to  REMOVAL [11/2018 - 10/2023] 

1. Remove the power back door sensor assembly RH.

   Refer to REMOVAL [11/2018 - ]

2. Inspect the power back door sensor assembly RH.

   Refer to INSPECTION [11/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE POWER BACK DOOR SENSOR ASSEMBLY RH. Refer to  REMOVAL [11/2018 - ] 

Result: 

OK 

See step  7

1. Disconnect the R8 power back door sensor assembly RH connector.
2. Disconnect the R18 multiplex network door ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R8-1 (OSR) - R18-6 (OSR)	Always	Below 1 Ω
   R8-2 (OSRE) - R18-24 (OSE)	Always	Below 1 Ω
   R8-1 (OSR) or R18-6 (OSR) - Body ground	Always	10 kΩ or higher
   R8-2 (OSRE) or R18-24 (OSE) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MULTIPLEX NETWORK DOOR ECU. Refer to  REMOVAL [11/2018 - 10/2023] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR 

1. Remove the power back door sensor assembly LH.

   Refer to REMOVAL [11/2018 - ]

2. Inspect the power back door sensor assembly LH.

   Refer to INSPECTION [11/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE POWER BACK DOOR SENSOR ASSEMBLY LH. Refer to  REMOVAL [11/2018 - ] 

Result: 

OK 

See step  9

1. Disconnect the R9 power back door sensor assembly LH connector.
2. Disconnect the R18 multiplex network door ECU connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   R9-1 (OSL) - R18-26 (OSL)	Always	Below 1 Ω
   R9-2 (OSLE) - R18-24 (OSE)	Always	Below 1 Ω
   R9-1 (OSL) or R18-26 (OSL) - Body ground	Always	10 kΩ or higher
   R9-2 (OSLE) or R18-24 (OSE) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE MULTIPLEX NETWORK DOOR ECU. Refer to  REMOVAL [11/2018 - 10/2023] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR