DTC P0710-11: Transmission Fluid Temperature Sensor "A" Circuit Short To Ground [11/2018 - ]: Procedure

1. Warm up the engine.
2. Turn the ignition switch off.
3. Connect the Techstream to the DLC3.
4. Turn the ignition switch to ON.
5. Turn the Techstream on.
6. Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No. 1.
7. Read the Data List according to the display on the Techstream.

   Powertrain > Transmission > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   A/T Oil Temperature No. 1	ATF temperature sensor value	Min.: -40°C (-40°F) Max.: 150°C (302°F)	Approximately 80°C (176°F): After stall speed test Equal to ambient temperature: When engine is cold	If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted

   Powertrain > Transmission > Data List 

   Tester Display
   A/T Oil Temperature No. 1

   Result

   Result	Proceed to
   Data List value is normal	A
   Data List value is not normal	B

Result: 

A 

See step  3

Result: 

B 

See step  2

1. Disconnect the ECM connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C41-46 (THO1) - C41-45 (ETHO)	Always	79 Ω to 156 kΩ
   C41-45 (ETHO) - Body ground	Always	10 kΩ or higher
   C41-46 (THO1) - Body ground	Always	10 kΩ or higher

   HINT: 

   If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

   ATF Temperature	Specified Condition
   10°C (50°F)	5 to 8 kΩ
   25°C (77°F)	2.5 to 4.5 kΩ
   110°C (230°F)	0.22 to 0.28 kΩ

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  4

Result: 

OK 

See step  3

1. Replace the ECM.

   Refer to REMOVAL [11/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

PERFORM REGISTRATION. Refer to  REGISTRATION [11/2018 - ] 

1. Disconnect the transmission wire connector.
2. Disconnect the ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C30-1 (OIL) or C41-46 (THO1) - Body ground	Always	10 kΩ or higher
   C30-2 (E2) or C41-45 (ETHO) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR). Refer to  REMOVAL [11/2018 - 10/2019]  , or refer to  REMOVAL [10/2019 - 08/2020]  , or refer to  REMOVAL [08/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - 10/2023]  , or refer to  REMOVAL [10/2023 - ] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)