DTC P0710-00: Transmission Fluid Temperature Sensor "A" Circuit Range/Performance [12/2021 - ]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Transmission / Trouble Codes.

   Powertrain > Transmission > Trouble Codes 

5. Read the DTCs using the Techstream.

   Result

   Result	Proceed to
   Only DTC P0710-00 is output	A
   DTC P0710-00 and P0710-15 are output	B
   DTC P0710-00 and other DTCs are output	C

   HINT: 

   If any DTCs other than DTC P0710-00 are output, perform troubleshooting for those DTCs first.

Result: 

B 

GO TO DTC CHART (DTC P0710-15) 

Refer to DTC P0710-15: Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open [08/2020 - ] 

Result: 

C 

GO TO DTC CHART 

Refer to DIAGNOSTIC TROUBLE CODE CHART [12/2021 - 10/2022] , or refer to DIAGNOSTIC TROUBLE CODE CHART [10/2022 - ]

Result: 

A 

See step  2

1. Check the automatic transaxle fluid level.

   Refer to ADJUSTMENT [12/2021 - ]

   OK

   Automatic transaxle fluid level is correct.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

ADJUST AUTOMATIC TRANSAXLE FLUID LEVEL 

Refer to ADJUSTMENT [12/2021 - ]

Result: 

OK 

See step  3

1. Disconnect the ECM connector.
2. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C41-46 (THO1) - C41-45 (ETHO)	ATF temperature 10°C (50°F)	5 to 8 kΩ
   C41-46 (THO1) - C41-45 (ETHO)	ATF temperature 110°C (230°F)	0.22 to 0.28 kΩ
   C41-45 (ETHO) - Body ground	Always	10 kΩ or higher
   C41-46 (THO1) - Body ground	Always	10 kΩ or higher

   HINT: 

   If the resistance is out of the specified range at the ATF temperature shown in the table below, the driveability of the vehicle may decrease.

   ATF Temperature	Specified Condition
   25°C (77°F)	2.5 to 4.5 kΩ

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  5

Result: 

OK 

See step  4

1. Replace the ECM.

   Refer to REMOVAL [08/2020 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

PERFORM REGISTRATION 

Refer to REGISTRATION [11/2018 - ]

1. Disconnect the transmission wire connector.
2. Disconnect the ECM connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   C30-1 (OIL) - C41-46 (THO1)	Always	Below 1 Ω
   C30-2 (E2) - C41-45 (ETHO)	Always	Below 1 Ω
   C30-1 (OIL) or C41-46 (THO1) - Body ground	Always	10 kΩ or higher
   C30-2 (E2) or C41-45 (ETHO) - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) 

Refer to REMOVAL [08/2020 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)