LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> RAV4 LE, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 70 (Lighting System (W/ AFS) - Diagnostic Codes & Circuit Tests) >> LIGHTING SYSTEM (w/ AFS) >> Hazard Warning Switch Circuit [02/2019 - 12/2021] >> Procedure

Hazard Warning Switch Circuit [02/2019 - 12/2021]: Procedure

WARNING: This page is about a different car, the 2021 Toyota RAV4, 2020 Toyota RAV4, and 2019 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ VALUE USING TECHSTREAM 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Combination Meter / Data List.
    5. Read the Data List according to the display on the Techstream.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Hazard Flasher Switch Hazard warning signal switch signal OFF or ON OFF: Hazard warning signal switch off
      ON: Hazard warning signal switch on      		 -

      Body Electrical > Combination Meter > Data List 

      Tester Display
      Hazard Flasher Switch

      OK

      Normal conditions listed above are displayed.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE [02/2019 - 08/2020]  , or refer to  PROBLEM SYMPTOMS TABLE [08/2020 - 12/2021] 

    Result: 

    NG 

    See step  2

  2. INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY 
    1. Remove the hazard warning signal switch assembly.

      Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

    2. Inspect the hazard warning signal switch assembly.

      Refer to INSPECTION [11/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY. Refer to  REMOVAL [02/2019 - 10/2019]  , or refer to  REMOVAL [10/2019 - 08/2020]  , or refer to  REMOVAL [08/2020 - 12/2021] 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the H2 hazard warning signal switch assembly connector.
    2. Disconnect the G19 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H2-5 (TB) - G19-17 (HAZ) Always Below 1 Ω
      H2-5 (TB) or G19-17 (HAZ) - Body ground Always 10 kΩ or higher
      H2-2 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2018 - 10/2022] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals