LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> RAV4 LE, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 65 (Lighting System (W/O Headlight Ecu) - Diagnostic Codes & Circuit Tests) >> LIGHTING SYSTEM (w/o Headlight ECU) >> DTC B2430: LED Headlight LH; DTC B2431: LED Headlight RH [02/2019 - 12/2021] >> Procedure

DTC B2430: LED Headlight LH; DTC B2431: LED Headlight RH [02/2019 - 12/2021]: Procedure

WARNING: This page is about a different car, the 2021 Toyota RAV4, 2020 Toyota RAV4, and 2019 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
  1. CLEAR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / Main Body / Clear DTCs.
    5. Clear the DTCs.

      Body Electrical > Main Body > Clear DTCs 

      Result

      Proceed to
      NEXT

    Result: 

    NEXT 

    See step  2

  2. CHECK FOR DTC 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON (READY).
    3. Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.
    4. Turn the Techstream on.
    5. Enter the following menus: Body Electrical / Main Body / Trouble Codes.
    6. Check for DTCs.

      Body Electrical > Main Body > Trouble Codes 

      OK

      DTC B2430 and B2431 are not output.

      Result

      Result Proceed to
      OK A
      NG (DTC B2430 is output) B
      NG (DTC B2431 is output) C

    Result: 

    A 

    USE SIMULATION METHOD TO CHECK 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ]

    Result: 

    C 

    See step  12

    Result: 

    B 

    See step  3

  3. CHECK HEADLIGHT UNIT ASSEMBLY LH (LO TERMINAL VOLTAGE) 
    1. Disconnect the headlight unit assembly LH connector.
      GTY911264Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headlight Unit Assembly LH)
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      A62-1 (LO) - Body ground Light control switch in HEAD position 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  7

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY LH - BODY GROUND) 
    1. Disconnect the headlight unit assembly LH connector.
      GTY911262Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headlight Unit Assembly LH)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A62-2 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK HEADLIGHT UNIT ASSEMBLY LH (S TERMINAL VOLTAGE) 
    1. Disconnect the headlight unit assembly LH connector.
      GTY942295Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headlight Unit Assembly LH)
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      A62-6 (S) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT UNIT ASSEMBLY LH 

    Refer to REMOVAL [02/2019 - 12/2021]

    Result: 

    NG 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) 
    1. Disconnect the A62 headlight unit assembly LH connector.
    2. Disconnect the G43 main body ECU (multiplex network body ECU) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A62-6 (S) - G43-14 (LLEW) Always Below 1 Ω
      A62-6 (S) or G43-14 (LLEW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  7. CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT UNIT ASSEMBLY LH) 
    1. Remove the H-LP LH relay.
    2. Disconnect the A62 headlight unit assembly LH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (H-LP LH relay) - A62-1 (LO) Always Below 1 Ω
      3 (H-LP LH relay) or A62-1 (LO) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. INSPECT H-LP LH RELAY 
    1. Remove the H-LP LH relay.
    2. Inspect the H-LP LH relay.

      Refer to ON-VEHICLE INSPECTION [02/2019 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE H-LP LH RELAY 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY) 
    1. Remove the H-LP LH relay.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      2 (H-LP LH relay) - Body ground Ignition switch off 11 to 14 V
      5 (H-LP LH relay) - Body ground Ignition switch off 11 to 14 V
      GTY510431Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to H-LP LH Relay)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  10

  10. CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) 
    1. Remove the H-LP LH relay.
    2. Disconnect the 4F instrument panel junction block assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (H-LP LH relay) - 4F-31 Always Below 1 Ω
      1 (H-LP LH relay) or 4F-31 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  11

  11. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 
    GTY895502Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Component without harness connected
    (Instrument Panel Junction Block Assembly)    		 - -
    1. Remove the instrument panel junction block assembly.

      Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4F-31 - A-15 (HRLY) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

    Result: 

    NG 

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 

    Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

  12. CHECK HEADLIGHT UNIT ASSEMBLY RH (LO TERMINAL VOLTAGE) 
    1. Disconnect the headlight unit assembly RH connector.
      GTY911263Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headlight Unit Assembly RH)
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      A61-1 (LO) - Body ground Light control switch in HEAD position 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  16

    Result: 

    OK 

    See step  13

  13. CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY RH - BODY GROUND) 
    1. Disconnect the headlight unit assembly RH connector.
      GTY911261Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headlight Unit Assembly RH)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A61-2 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  14

  14. INSPECT HEADLIGHT UNIT ASSEMBLY RH (S TERMINAL VOLTAGE) 
    1. Disconnect the headlight unit assembly RH connector.
      GTY911258Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Headlight Unit Assembly RH)
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      A61-6 (S) - Body ground Ignition switch ON 11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HEADLIGHT UNIT ASSEMBLY RH 

    Refer to REMOVAL [02/2019 - 12/2021]

    Result: 

    NG 

    See step  15

  15. CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) 
    1. Disconnect the A61 headlight unit assembly RH connector.
    2. Disconnect the G43 main body ECU (multiplex network body ECU) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A61-6 (S) - G43-15 (RLEW) Always Below 1 Ω
      A61-6 (S) or G43-15 (RLEW) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  16. CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT UNIT ASSEMBLY RH) 
    1. Remove the H-LP RH relay.
    2. Disconnect the A61 headlight unit assembly RH connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (H-LP RH relay) - A61-1 (LO) Always Below 1 Ω
      3 (H-LP RH relay) or A61-1 (LO) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  17

  17. INSPECT H-LP RH RELAY 
    1. Remove the H-LP RH relay.
    2. Inspect the H-LP RH relay.

      Refer to ON-VEHICLE INSPECTION [02/2019 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE H-LP RH RELAY 

    Result: 

    OK 

    See step  18

  18. CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY) 
    1. Remove the H-LP RH relay.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      2 (H-LP RH relay) - Body ground Ignition switch off 11 to 14 V
      5 (H-LP RH relay) - Body ground Ignition switch off 11 to 14 V
      GTY510431Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to H-LP RH Relay)

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  19

  19. CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) 
    1. Remove the H-LP RH relay.
    2. Disconnect the G44 main body ECU (multiplex network body ECU) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      1 (H-LP RH relay) - G44-12 (HRY2) Always Below 1 Ω
      1 (H-LP RH relay) or G44-12 (HRY2) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 

    Refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals