Data List / Active Test [10/2023 - 11/2024]

HINT: 

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. According to the display on the GTS, read the Data List.

   Body Electrical > Back Door > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Total Distance Traveled	Total distance traveled	0 to 16777215	Same as actual total distance traveled	For the unit, refer to "Total Distance Traveled - Unit"
   Total Distance Traveled - Unit	Total Distance Traveled - unit	km or mile	km: km mile: mile	-
   Back Door Lock Status	Back door condition signal	Lock or Unlock	Lock: Back door locked Unlock: Back door unlocked	-
   Half Latch Switch	Latch switch signal	ON or OFF	ON: When in the open latch or overstroke position OFF: Half latch position → full latch position	-
   Closer Position Switch	Initial switch signal	ON or OFF	ON: Back door lock sector gear in center position (Initial switch on) OFF: Back door lock sector gear out of center position (Initial switch off)	-
   Pawl Switch	Pawl switch signal	ON or OFF	ON: Back door lock motor open-latched OFF: Back door lock motor except open latched	-
   Courtesy Switch	Back door courtesy switch signal	ON or OFF	ON: Open latch position → half latch position OFF: Full latch position → overstroke position	-
   PBD Main Switch	Power back door ON/OFF signal	ON or OFF	Current customize setting displayed	-
   PBD Close Switch	No. 1 power back door control switch signal	ON or OFF	ON: No. 1 power back door control switch pushed OFF: No. 1 power back door control switch not pushed	-
   IG Switch	Ignition switch signal	ON or OFF	ON: Ignition switch ON OFF: Ignition switch off	"OFF" is also displayed for this item when the ignition switch to ACC.
   Kick Sensor Function	Status of the hands free power back door function*	ON or OFF	ON: Hands free power back door ON OFF: Hands free power back door off	-
   Door Lock Signal	Back door condition signal	Lock or Unlock	Lock: Back door locked Unlock: Back door unlocked	-
   Status of Kick Sensor Detection	Kick door control sensor ON detection status*	ON or OFF	ON: Kick door control sensor ON detected OFF: Kick door control sensor ON not detected	-
   Status of Kick Sensor Abnormal	Kick door control sensor abnormal condition*	Normal or Abnormal	Normal: Kick door control sensor normal Abnormal: Kick door control sensor abnormal	-
   Kick Sensor Installation	Kick door control sensor installed condition*	ON or OFF	ON: Kick door control sensor incorrectly installed OFF: Kick door control sensor correctly installed	-
   PBD Touch Sensor RH	Power back door sensor assembly RH signal	ON, OFF or Open	ON: Power back door sensor assembly RH pressed OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open	-
   PBD Touch Sensor LH	Power back door sensor assembly LH signal	ON, OFF or Open	ON: Power back door sensor assembly LH pressed OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open	-
   Correction of Back Door Position	Correction of back door position	Not Complied With or Complied With	Not Complied With: not complied with Complied With: complied with	-
   PBD Close Switch Operation History	Power back door control switch operation history	ON or OFF	ON: Has operation history OFF: No operation history	The operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds.
   Close & Lock Switch Operation History	Back door control switch operation history	ON or OFF	ON: Has operation history OFF: No operation history	Although the item is displayed on the GTS, it is not applicable to this vehicle
   Kick Sensor Status	Kick Sensor condition signal*	Normal, Sensitivity Low (Noise), Stop (Foreign Objects), Sensitivity Low (Noise) & Stop (Foreign Objects), Stop (Battery Protection), Sensitivity Low (Noise) & Stop (Battery Protection), Stop (Foreign Objects) & Stop (Battery Protection) or Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection)	Normal: Kick sensor detection status normal Sensitivity Low (Noise): Kick sensor detection sensitivity decreased due to noise Stop (Foreign Objects): Kick sensor detection stopped due to foreign objects Sensitivity Low (Noise) & Stop (Foreign Objects): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects Stop (Battery Protection): Kick sensor detection stopped due to battery protection Sensitivity Low (Noise) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to battery protection Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor detection stopped due to foreign objects and battery protection Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects and battery protection	-
   Opened Number of Times	Number of times for back door opened	0 to 214783647	Number of times for back door opened	-
   Closed Number of Times	Number of times for back door closed	0 to 214783647	Number of times for back door closed	-
   PBD SW Operating Condition Setting	Back door control switch operation	ON or 0.8s	Current customize setting displayed	-
   PBD Buzzer Function	Status of the power back door warning buzzer	ON or OFF	Current customize setting displayed	-
   PBD Assist Close Function	Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually.	ON or OFF	Current customize setting displayed	-
   PBD Assist Open Function	Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated.	ON or OFF	Current customize setting displayed	-
   PBD Door Unlock with One Motion Setting	Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly).	Back Door or All Doors	Current customize setting displayed	-
   PBD Wireless Function	Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).	ON or OFF	Current customize setting displayed	-
   PBD Wireless One Motion Function	Wireless one motion function	ON or OFF	Current customize setting displayed	-
   PBD Wireless SW Setting	Wireless operation setting condition	1 Time Press, 2 Times Press or Long Press (0.8s)	Current customize setting displayed	-
   PBD Kick Sensor Sensitivity Adjust	Function that changes the sensitivity of the kick sensor.*	Normal, +1, +2 or Unknown	Current customize setting displayed	-
   PBD Kick-in Beep Sound	Function that sounds a buzzer when a kick operation detected.*	ON or OFF	Current customize setting displayed	-

   1. *: w/ Hands Free Power Back Door

   for Type A:

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Back Door Lock Position Status	Back door lock position signal	Lock or Unlock	Lock: Back door locked Unlock: Back door unlocked	-
   Back Door Courtesy Switch Status	Back door courtesy light switch signal	Close or Open	Close: Back door closed Open: Back door open	-
   Back Door Operation Switch (Instrument)	Power back door control switch signal	ON or OFF	ON: Power back door control switch on OFF: Power back door control switch off	-

   for Type B:

   Body Electrical > Main Body > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Back Door Courtesy SW	Back door courtesy switch signal	ON or OFF	ON: Back door open OFF: Back door closed	-
   Back Door Open	Back door condition signal	Permit or Prohibit	Permit: Back door unlocked Prohibit: Back door locked	-
   Back Door Open SW	Power back door switch assembly signal	ON or OFF	ON: Power back door switch assembly on OFF: Power back door switch assembly off	-
   Back Door Open Handle SW	Back door opener switch assembly (open switch) signal	ON or OFF	ON: Back door opener switch assembly (open switch) on OFF: Back door opener switch assembly (open switch) off	-
   Kick Sensor Operation with ACC ON	Status of the hands free power back door function with power switch on (ACC)*	Not Available or Available	Current customize setting displayed	-

   1. *: w/ Hands Free Power Back Door

HINT: 

Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

1. According to the display on GTS perform the "Active Test".

   Body Electrical > Back Door > Active Test 

   Tester Display	Measurement Item	Control Range	Diagnostic Note
   PBD Motor (Open)	Power back door motor operation	Start	-
   PBD Motor (Close)	Power back door motor operation	Start	-
   PBD Buzzer (Small Volume)	Power back door warning buzzer sound (small volume)	Start	-
   PBD Buzzer (Middle Volume)	Power back door warning buzzer sound (Middle volume)	Start	-
   PBD Buzzer (Large Volume)	Power back door warning buzzer sound (Large volume)	Start	-
   PBD Release Closer	Latch release operation	Start	-