LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> Prius LE AWD-e >> Repair and Diagnosis >> External Pages >> Different car >> Section 253 (Supplemental Restraint System - Diagnostic Codes (B1660-U0154) & Symptom Tests (Except Hybrid)) >> AIRBAG SYSTEM (for Gasoline Model) >> Symptom Tests >> SRS Warning Light Remains ON [08/2020 -] >> Procedure

SRS Warning Light Remains ON [08/2020 -]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Avalon, 2021 Toyota Avalon, 2020 Toyota Avalon, and 2019 Toyota Avalon. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK SRS WARNING LIGHT OPERATION 
    1. Turn the engine switch on (IG) and check the SRS warning light condition.

      HINT: 

      The primary check is performed for approximately 6 seconds after the engine switch is turned on (IG).

      Result

      Result Proceed to
      After the primary check period, the SRS warning light remains on. A
      After the primary check period, the SRS warning light turns off and comes on again. B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  2

  2. CHECK BATTERY VOLTAGE 
    1. Measure the voltage of the battery.

      Standard Voltage

      11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    INSPECT CHARGING SYSTEM AND BATTERY 

    for 2GR-FKS: Refer to ON-VEHICLE INSPECTION [04/2018 -]

    for A25A-FKS: Refer to ON-VEHICLE INSPECTION [08/2020 -]

    Result: 

    OK 

    See step  3

  3. CHECK CONNECTOR 
    1. Turn the engine switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag ECU assembly.

      OK

      The connector is properly connected.

      HINT: 

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag ECU assembly.
    5. Check that the terminals of the connector are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE WIRE HARNESS 

    Result: 

    OK 

    See step  4

  4. CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY911108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
    2. Turn the engine switch on (IG).
    3. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G50-36 (IG2) - Body ground Engine switch on (IG) 8 to 16 V
    5. Turn the engine switch off.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G50-33 (E1) - Body ground Always Below 1 Ω
      G50-32 (E2) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE WIRE HARNESS 

    Result: 

    OK 

    See step  5

  5. CHECK SRS WARNING LIGHT 
    1. Turn the engine switch on (IG) and check the SRS warning light condition.

      OK

      After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.

      HINT: 

      The primary check period is approximately 6 seconds after the engine switch is turned on (IG).

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 -] 

    Result: 

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 -] 

  6. CHECK CAN COMMUNICATION SYSTEM 
    1. Using the Techstream, check if the CAN communication system is functioning normally.

      OK

      CAN communication system is functioning normally.

      HINT: 

      Refer to Communication Bus Check in CAN Communication System.

      Refer to DIAGNOSIS SYSTEM [08/2020 - 08/2021] , or refer to DIAGNOSIS SYSTEM [08/2021 -]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    GO TO CAN COMMUNICATION SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [04/2018 -] 

    Result: 

    OK 

    See step  7

  7. CHECK BATTERY VOLTAGE 
    1. Measure the voltage of the battery.

      Standard Voltage

      11 to 14 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    INSPECT CHARGING SYSTEM AND BATTERY 

    for 2GR-FKS: Refer to ON-VEHICLE INSPECTION [04/2018 -]

    for A25A-FKS: Refer to ON-VEHICLE INSPECTION [08/2020 -]

    Result: 

    OK 

    See step  8

  8. CHECK CONNECTOR 
    1. Turn the engine switch off.
    2. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag ECU assembly.

      OK

      The connector is properly connected.

      HINT: 

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag ECU assembly.
    5. Check that the terminals of the connector are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE WIRE HARNESS 

    Result: 

    OK 

    See step  9

  9. CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY911108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Airbag ECU Assembly)
    2. Turn the engine switch on (IG).
    3. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G50-36 (IG2) - Body ground Engine switch on (IG) 8 to 16 V
    5. Turn the engine switch off.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G50-33 (E1) - Body ground Always Below 1 Ω
      G50-32 (E2) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE WIRE HARNESS 

    Result: 

    OK 

    See step  10

  10. CHECK CONNECTOR 
    1. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Check that the connector is properly connected to the combination meter assembly.

      OK

      The connector is properly connected.

      HINT: 

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    3. Disconnect the connector from the combination meter assembly.
    4. Check that the terminals of the connector are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE CONNECTOR 

    Result: 

    OK 

    See step  11

  11. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND) 
    1. Connect the cable to the negative (-) battery terminal.
      GTY926038Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Combination Meter Assembly)
    2. Turn the engine switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G16-39 (IG+) - Body ground Engine switch on (IG) 11 to 14 V
      G16-40 (B) - Body ground Always 11 to 14 V
    4. Turn the engine switch off.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G16-21 (ES) - Body ground Always Below 1 Ω
      G16-2 (EP) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE WIRE HARNESS 

    Result: 

    OK 

    See step  12

  12. CHECK SRS WARNING LIGHT 
    1. Disconnect the cable from the negative (-) battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Connect the connector to the combination meter assembly.
    3. Connect the cable to the negative (-) battery terminal.
    4. Turn the engine switch on (IG) and check the SRS warning light condition.

      OK

      After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.

      HINT: 

      The primary check period is approximately 6 seconds after the engine switch is turned on (IG).

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 -] 

    Result: 

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 -] 

scientia non olet · About LEMON Manuals