LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> Corolla Cross L, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 88 (Hybrid Control System - Circuit Tests (2 Of 2)) >> Hybrid Control System >> Drive Mode Select Switch Circuit [11/2022 - ] >> Procedure

Drive Mode Select Switch Circuit [11/2022 - ]: Procedure

WARNING: This page is about a different car, the 2025 Toyota Corolla Cross, 2024 Toyota Corolla Cross, and 2023 Toyota Corolla Cross. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ VALUE USING GTS (CAN BUS CHECK) 

    See step  1

    Result

    Result Proceed to
    All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
    None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B

    Result: 

    B 

    GO TO CAN COMMUNICATION SYSTEM 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - 11/2023] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2023 - 12/2024] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2024 - ]

    Result: 

    A 

    See step  2

  2. CHECK DTC OUTPUT (HEALTH CHECK) 

    See step  1

    Result

    Result Proceed to
    No DTCs are output A
    DTCs are output B

    Result: 

    B 

    GO TO  DIAGNOSTIC TROUBLE CODE CHART [11/2022 - 12/2024] 

    Result: 

    A 

    See step  3

  3. CHECK DRIVE MODE STATUS 
    1. Turn the ignition switch to ON.
    2. Operate the drive mode select switch (combination switch assembly) to change the drive mode.
    3. Check that the drive mode indicator is displayed on the multi-information display and changes according to the selected drive mode.

      Result

      Result Proceed to
      The display changes according to the drive mode select switch operation A
      The display does not change according to the drive mode select switch operation
      (For Push Type Switch)      		 B
      The display does not change according to the drive mode select switch operation
      (For Toggle Type Switch)      		 C
    4. Turn the ignition switch off.

    Result: 

    A 

    GO TO PROBLEM SYMPTOMS TABLE 

    Refer to PROBLEM SYMPTOMS TABLE [11/2022 - ]

    Result: 

    C 

    See step  8

    Result: 

    B 

    See step  4

  4. READ VALUE USING GTS (POWERTRAIN DRIVE MODE SWITCH) 
    1. Read the value displayed on the GTS.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Powertrain Drive Mode Switch

      Result

      Result Proceed to
      The display changes according to the drive mode select switch operation A
      Other than above B
    2. Turn the ignition switch off.

    Result: 

    A 

    CHECK METER / GAUGE SYSTEM 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - ]

    Result: 

    B 

    See step  5

  5. INSPECT DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) 

    Refer to INSPECTION [11/2022 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE COMBINATION SWITCH ASSEMBLY 

    Refer to REMOVAL [11/2022 - ]

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND) 
    1. Disconnect the drive mode select switch (combination switch assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I61-5 (E) - Body ground Always Below 1 Ω
    3. Reconnect the drive mode select switch (combination switch assembly) connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY)) 
    1. Disconnect the hybrid vehicle control ECU connector.
    2. Disconnect the drive mode select switch (combination switch assembly) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I249-37 (PDRV) - I61-6 (DRV) Always Below 1 Ω
      I249-37 (PDRV) or I61-6 (DRV) - Body ground Always 10 kΩ or higher
    4. Reconnect the drive mode select switch (combination switch assembly) connector.
    5. Reconnect the hybrid vehicle control ECU connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU 

    Refer to REMOVAL [11/2022 - 12/2024] , or refer to REMOVAL [12/2024 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  8. READ VALUE USING GTS (DRIVE MODE SWITCH) 
    1. Read the value displayed on the GTS.

      Powertrain > Hybrid Control > Data List 

      Tester Display
      Drive Mode Switch-
      Drive Mode Switch+

      Result

      Result Proceed to
      The display changes according to the drive mode select switch operation A
      Other than above B
    2. Turn the ignition switch off.

    Result: 

    A 

    CHECK METER / GAUGE SYSTEM 

    Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - ]

    Result: 

    B 

    See step  9

  9. INSPECT DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) 

    Refer to INSPECTION [11/2022 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE COMBINATION SWITCH ASSEMBLY 

    Refer to REMOVAL [11/2022 - ]

    Result: 

    OK 

    See step  10

  10. CHECK HARNESS AND CONNECTOR (DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND) 
    1. Disconnect the drive mode select switch (combination switch assembly) connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I61-5 (E) - Body ground Always Below 1 Ω
    3. Reconnect the drive mode select switch (combination switch assembly) connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  11

  11. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SELECT SWITCH (COMBINATION SWITCH ASSEMBLY)) 
    1. Disconnect the hybrid vehicle control ECU connector.
    2. Disconnect the drive mode select switch (combination switch assembly) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      I249-37 (DMS-) - I61-6 (E) Always Below 1 Ω
      I249-38 (DMS+) - I61-7 (SEL) Always Below 1 Ω
      I249-37 (DMS-) or I61-6 (E) - Body ground Always 10 kΩ or higher
      I249-38 (DMS+) or I61-7 (SEL) - Body ground Always 10 kΩ or higher
    4. Reconnect the drive mode select switch (combination switch assembly) connector.
    5. Reconnect the hybrid vehicle control ECU connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU 

    Refer to REMOVAL [11/2022 - 12/2024] , or refer to REMOVAL [12/2024 - ]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals