Caution / Notice / Hint

WARNING: This page is about a different car, the 2025 Toyota Corolla Cross and 2024 Toyota Corolla Cross. However, it is still accessible from the selected car via links, so may be relevant.

COMPONENTS (REMOVAL)

Fig 1: K121 Transmission Control Cable Removal Components (1 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1	SECURE VEHICLE	-	See step 1	-	-
2	AUXILIARY BATTERY	-	-	-	-
3	ECM	89661	-	-	-
4	BATTERY CLAMP SUB-ASSEMBLY	74404A	-	-	-

Fig 2: K121 Transmission Control Cable Removal Components (2 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5	FRONT FLOOR CENTER BRACE	57533B	-	-	-
6	FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)	17410	See step 6	-	-
7	FRONT NO. 1 FLOOR HEAT INSULATOR	58151	-	-	-

•

Non-reusable part

Fig 3: K121 Transmission Control Cable Removal Components (3 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8	SHIFT LOCK RELEASE BUTTON COVER	33554C	See step 8	-	-

Fig 4: K121 Transmission Control Cable Removal Components (4 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9	CONSOLE BOX ASSEMBLY	58810J	-	-	-
10	NO. 3 CONSOLE BOX DUCT	58863A	-	-	-
11	NO. 2 CONSOLE BOX DUCT	58862B	-	-	-
12	NO. 1 CONSOLE BOX DUCT	58861B	-	-	-

Fig 5: K121 Transmission Control Cable Removal Components (5 Of 5)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
13	DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (Shift Lever Side)	33820B	See step 13	-	-
14	DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (Transaxle Side)	33820B	See step 14	-	-
15	REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY	33820B	-	-	-

•

Non-reusable part

WARNING:

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front camera system	Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more.	Refer to INITIALIZATION [11/2022 - ]
Stop and start system	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Refer to PRECAUTION [11/2023 - ]

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power door lock control system Back door opener	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.	Refer to INITIALIZATION [11/2022 - ]
Power back door system	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.	Refer to INITIALIZATION [09/2021 - ]
Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized.	-