How To Proceed With Troubleshooting [11/2022 - ]: Procedure

Result

Result: 

NEXT 

See step  2

1. Interview the customer and confirm the problem.

   Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2021 - ]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  3

1. Check and record DTCs and Freeze Frame Data.

   for DTC Check / Clear: Refer to DTC CHECK / CLEAR [11/2022 - 11/2023] , or refer to DTC CHECK / CLEAR [11/2023 - ] 

   for Freeze Frame Data: Refer to FREEZE FRAME DATA [11/2022 - ] 

   Chassis > Brake/EPB > Trouble Codes 

2. Clear the DTCs and Freeze Frame Data.

   for DTC Check / Clear: Refer to DTC CHECK / CLEAR [11/2022 - 11/2023] , or refer to DTC CHECK / CLEAR [11/2023 - ] 

   for Freeze Frame Data: Refer to FREEZE FRAME DATA [11/2022 - ] 

   Chassis > Brake/EPB > Clear DTCs 

3. Reconfirm the DTCs.
   1. Reconfirm the DTCs based on the recorded DTCs and Freeze Frame Data.

      for DTC Check / Clear: Refer to DTC CHECK / CLEAR [11/2022 - 11/2023] , or refer to DTC CHECK / CLEAR [11/2023 - ] 

      for Freeze Frame Data: Refer to FREEZE FRAME DATA [11/2022 - ] 

      Chassis > Brake/EPB > Trouble Codes 

      HINT: 

      • When CAN communication system DTCs are output, repair the CAN communication system first.

        Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - 11/2023] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2023 - 12/2024] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2024 - ]

      • If DTCs related to momentary interruptions are output, perform troubleshooting for those DTCs first.

        Refer to DATA LIST / ACTIVE TEST [11/2022 - ] 

      • If the GTS cannot communicate with the skid control ECU (brake actuator assembly), inspect the CAN communication system.

        Refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2022 - 11/2023] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [11/2023 - 12/2024] , or refer to HOW TO PROCEED WITH TROUBLESHOOTING [12/2024 - ]

      • If there is no response from the skid control ECU (brake actuator assembly), inspect the supply power circuit.

        Refer to TERMINALS OF ECU [11/2022 - ] 

4. Check the Vehicle Control History (RoB).

   Refer to VEHICLE CONTROL HISTORY (RoB) [11/2022 - 11/2023] , or refer to VEHICLE CONTROL HISTORY (RoB) [11/2023 - ]

   Chassis > Brake/EPB > Utility 

   Tester Display
   Vehicle Control History (RoB)

   Chassis > Steering Angle Sensor > Utility 

   Tester Display
   Vehicle Control History (RoB)

   Result

   Result	Proceed to
   DTCs are not output. (Problem symptom occurs.)	A
   DTCs are output.	B
   DTCs are not output. (Problem symptom does not occur.)	C
   DTCs are not output. (Vehicle control history (RoB) is stored.)	D

Result: 

A 

CONFIRM PROBLEM SYMPTOMS 

Refer to PROBLEM SYMPTOMS TABLE [11/2022 - ] 

Result: 

B 

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS* 

Result: 

C 

USE SIMULATION METHOD TO CHECK 

Refer to HOW TO PROCEED WITH TROUBLESHOOTING [09/2021 - ]

Result: 

D 

REPAIR TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY (RoB)* 

Refer to VEHICLE CONTROL HISTORY (RoB) [11/2022 - 11/2023] , or refer to VEHICLE CONTROL HISTORY (RoB) [11/2023 - ]