Installation [04/2018 - 08/2020]: Procedure

Refer to PROCEDURE - Step 1 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 1 [08/2019 - 08/2021]

1. Connect each connector.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Install in this Direction

   -

   -

2. Engage each clamp.
3. Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
4. Install the 4 bolts (A).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   	Bolt (A)		Bolt (B)
   	Nut	-	-

   Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) 

5. Connect the brake pedal assembly with the bolt (B).

   Torque: 15 N*m (153 kgf*cm, 11 ft.*lbf) 

6. Temporarily install the nut.
7. Install the 3 bolts.

   Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) 

8. Install the 2 hole plugs.
9. Install a new cooler unit drain hose grommet.
   NOTE:

   • If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.
   • Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a

   Lip

10. Connect the drain cooler hose.

11. Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Install the front floor mat to its original position as shown in the illustration.

12. Engage each clamp.

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    *a	Lock Lever
    	Move in this Direction

13. Temporarily connect the connector and then move the lock lever as shown in the illustration to securely connect the connector.
    NOTE:

    When connecting any airbag connector, take care not to damage the airbag wire harness.

14. Check that there is no looseness in the installed parts of the airbag sensor assembly.
15. Connect the connector.
16. Engage each clamp.
17. Connect the connector holder with the 2 nuts.

    Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

18. Connect the 3 earth wires with the 3 bolts.

    Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

19. Connect the connector.

Refer to PROCEDURE - Step 3

Refer to PROCEDURE - Step 5 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 5 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 6 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 6 [08/2019 - 08/2021]

1. Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

   Bolt 

   Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

   Nut 

   Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

2. Temporarily install the screw.

   HINT: 

   Do not fully tighten the screw.

3. Engage each clamp.
4. Connect the earth wire with the bolt.

   Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf) 

Refer to PROCEDURE - Step 8 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 8 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 9 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 9 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 10 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 10 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 11 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 11 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 12 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 12 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 13 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 13 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 14 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 14 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 15 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 15 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 16 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 16 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 1

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 19 [04/2018 - 08/2019] , or refer to PROCEDURE - Step 19 [08/2019 - 08/2021]

Refer to PROCEDURE - Step 1 [04/2018 - 08/2021]

Refer to PROCEDURE - Step 1

Refer to PROCEDURE - Step 6

Refer to PROCEDURE - Step 1

Refer to PROCEDURE - Step 2

Refer to INSTALLATION [04/2018 -]

for Manual Tilt and Manual Telescopic Steering Column:

Refer to INSTALLATION [04/2018 -]

for Power Tilt and Power Telescopic Steering Column:

Refer to INSTALLATION [04/2018 -]

Refer to INSTALLATION [04/2018 -]

Refer to INSTALLATION [04/2018 - 08/2020]

HINT: 

Use the same procedure as for the LH side.

1. Remove the vinyl tape from the No. 2 air conditioning tube and accessory assembly.
2. Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioning tube and accessory assembly.

   Compressor Oil

   ND-OIL 12 or equivalent

3. Install the 2 O-rings to the No. 2 air conditioning tube and accessory assembly.
   NOTE:

   Keep the O-rings and O-ring fitting surfaces free of foreign matter.

4. Connect the No. 2 air conditioning tube and accessory assembly.
5. Rotate the hook connector as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

6. Insert the tube joint into the fitting hole securely and install the bolt.

   Torque: 9.8 N*m (100 kgf*cm, 87 in.*lbf) 

1. Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.
   NOTE:

   Do not apply excessive force to the inlet heater water hose.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View A
   *b	Marking (Yellow)
   *c	Clip Installation Angle (270°)

1. Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	View A
   *b	Marking (Purple)
   *c	Clip Installation Angle (270°)

   NOTE:

   Do not apply excessive force to the outlet heater water hose.

Refer to PROCEDURE - Step 5

Refer to INSTALLATION [04/2018 -]

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 1

Refer to PROCEDURE - Step 2

Refer to PROCEDURE - Step 3

Refer to PROCEDURE - Step 5