DTC P0012-00: Camshaft Position "A" - Timing Over-Retarded Bank 1 [04/2018 -]: Procedure

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Powertrain / Engine / Trouble Codes.
5. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTC P0012-00 is output	A
   DTC P0012-00 and other DTCs are output	B

   HINT: 

   If any DTCs other than P0012-00 are output, troubleshoot those DTCs first.

Result: 

B 

GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART [04/2018 - 08/2019]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2019 - 08/2020]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2020 - 08/2021]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2021 -] 

Result: 

A 

See step  2

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the cam timing control motor with EDU assembly.

   Refer to REMOVAL [04/2018 - 08/2021] , or refer to REMOVAL [08/2021 -]

2. Check if the eccentric shaft of the camshaft timing gear assembly rotates smoothly.
   NOTE:

   If the camshaft is at a position where a valve is about to open, the eccentric shaft may become difficult to rotate.

   OK

   Rotates smoothly.

   HINT: 

   Perform "Inspection After Repair" after replacing the camshaft timing gear assembly, or removing the cam timing control motor with EDU assembly.

   Refer to INITIALIZATION [04/2018 - 08/2019] , or refer to INITIALIZATION [08/2019 - 08/2021] , or refer to INITIALIZATION [08/2021 -]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY. Refer to  PROCEDURE - Step 30 [04/2018 - 08/2019]  , or refer to  PROCEDURE - Step 30 [08/2019 -] 

Result: 

OK 

See step  3

1. Replace the cam timing control motor with EDU assembly.

   Refer to REMOVAL [04/2018 - 08/2021] , or refer to REMOVAL [08/2021 -]

   HINT: 

   Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.

   Refer to INITIALIZATION [04/2018 - 08/2019] , or refer to INITIALIZATION [08/2019 - 08/2021] , or refer to INITIALIZATION [08/2021 -]

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG).
3. Turn the Techstream on.
4. Clear the DTCs.

   Powertrain > Engine > Clear DTCs 

5. Turn the power switch off and wait for at least 30 seconds.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  5

1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
2. Enter the following menus: Powertrain / Engine / Trouble Codes.
3. Read the DTCs.

   Powertrain > Engine > Trouble Codes 

   Result

   Result	Proceed to
   DTCs are not output	A
   DTC P0012-00 is output	B

Result: 

A 

END 

Result: 

B 

REPLACE ECM. Refer to  REMOVAL [04/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 -]