LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> Avalon XLE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 47 (Meter / Gauge / Display - Diagnostic Codes & Symptom Tests (Hybrid)) >> METER / GAUGE SYSTEM (for HV Model) >> Circuit Tests >> Steering Pad Switch Circuit [04/2018 - ] >> Procedure

Steering Pad Switch Circuit [04/2018 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSPECT STEERING PAD SWITCH ASSEMBLY 
    1. Remove the steering pad switch assembly.

      Refer to REMOVAL [04/2018 - 08/2021] , or refer to REMOVAL [08/2021 - ]

    2. Inspect the steering pad switch assembly.

      Refer to INSPECTION [04/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE STEERING PAD SWITCH ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2021]  , or refer to  REMOVAL [08/2021 - ] 

    Result: 

    OK 

    See step  2

  2. INSPECT SPIRAL CABLE SUB-ASSEMBLY 
    1. Remove the spiral cable sub-assembly.

      Refer to REMOVAL [04/2018 - 08/2020] , or refer to REMOVAL [08/2020 - 08/2021] , or refer to REMOVAL [08/2021 - ]

    2. Inspect the spiral cable sub-assembly.

      Refer to INSPECTION [04/2018 - ]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE SPIRAL CABLE SUB-ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - ] 

    Result: 

    OK 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the G16 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G17-11 (+DP) - G16-29 (MSTI) Always Below 1 Ω
      G17-10 (+DP2) - G16-28 (MSM+) Always Below 1 Ω
      G17-11 (+DP) or G16-29 (MSTI) - Body ground Always 10 kΩ or higher
      G17-10 (+DP2) or G16-28 (MSM+) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) 
    GTY937352Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Spiral Cable Sub-assembly)
    1. Connect the G16 combination meter assembly connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      G17-11 (+DP) - Body ground Power switch on (IG) 4.8 to 5.2 V
      G17-10 (+DP2) - Body ground Power switch on (IG) 4.8 to 5.2 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [04/2018 - 08/2020]  , or refer to  REMOVAL [08/2020 - 08/2021]  , or refer to  REMOVAL [08/2021 - ] 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) 
    1. Disconnect the G3 radio and display receiver assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G17-4 (EAU) - G3-24 (SWG) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BODY GROUND) 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G3-1 (GND1) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [04/2018 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals