LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> Avalon XLE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 40 (Hybrid Transmission (Service Information) [P710]) >> Input Shaft Oil Seal >> Replacement [04/2018 - 08/2021] >> Caution / Notice / Hint

Caution / Notice / Hint

WARNING: This page is about a different variant/trim than selected.

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during input shaft type T oil seal removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) Refer to INITIALIZATION [04/2018 - 08/2021]
Pre-collision system
Intelligent clearance sonar system*
Lighting system (w/ AFS) (EXT)
Memorize steering angle neutral point Parking assist monitor system Refer to INITIALIZATION [04/2018 - ]
Panoramic view monitor system Refer to INITIALIZATION [04/2018 - ]
Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL illuminates Refer to REGISTRATION [04/2018 - ]
  • Replacement of engine assembly
  • Replacement of air fuel ratio sensor (sensor 2)
  • Replacement of engine coolant temperature sensor
  • Gas leak from exhaust system is repaired
 Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.
 Refer to INITIALIZATION [04/2018 - 08/2019] , or refer to INITIALIZATION [08/2019 - 08/2021]
Replacement of inverter with converter assembly Resolver learning
  • DTCs are stored
  • Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
  • Shock or vibration during acceleration
 Refer to UTILITY [04/2018 - 08/2020] , or refer to UTILITY [08/2020 - ]
Front wheel alignment adjustment
  1. Clear zero point calibration data.
  2. Perform yaw rate and acceleration sensor zero point calibration.
  • DTCs are stored
  • ABS warning light illuminates
  • Brake warning light / yellow (minor malfunction) illuminates
  • Slip indicator light illuminates
  • VSC disabled or malfunctions
 Refer to CALIBRATION [04/2018 - 08/2021]
  • Suspension, tires, etc.*1
  • Replacement of front bumper assembly
  • Measurement of ultrasonic sensor detection angle
  • Ultrasonic sensor detection angle registration
  • Intelligent clearance sonar system
  • Intuitive parking assist system
 Refer to CALIBRATION [04/2018 - ]
Suspension, tires, etc.*1 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system Refer to INITIALIZATION [04/2018 - ] for Initialization
Refer to CALIBRATION [04/2018 - ] for Calibration
Replacement of front bumper assembly Front television camera view adjustment Panoramic view monitor system Refer to INITIALIZATION [04/2018 - ] for Initialization
Refer to CALIBRATION [04/2018 - ] for Calibration
Suspension, tires, etc.*1
  • Television camera controller initialization
  • Adjust steering angle
  • Rear television camera assembly optical axis (Back camera position setting)
  • Replacement of headlight ECU sub-assembly LH
  • Replacement of headlight assembly LH
  • Synchronize the vehicle information
  • Perform headlight ECU sub-assembly LH initialization
 Lighting system (w/ AFS) (EXT) Refer to INITIALIZATION [04/2018 - ]
Suspension, tires, etc.*1 Perform headlight ECU sub-assembly LH initialization

*: When performing learning using the Techstream.

.*1: The vehicle height changes because of suspension or tire replacement

WARNING:
  • Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair information.
    GTY588409Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Refer to PRECAUTION [04/2018 - 08/2020] , or refer to PRECAUTION [08/2020 - 08/2021]

  • To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
    GTY588386Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  • To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
    GTY563662Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
    GTY563663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  • The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair information, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
    GTY566510Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a An Object Exceeding Weight Limit of Engine Lifter
  • The hybrid vehicle transaxle assembly is very heavy. Be sure to follow the procedure described in the repair information, or the transmission jack may suddenly drop or a part may fall.
    GTY559497Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Object Exceeding Weight Limit of Transmission Jack
NOTE:
  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [04/2018 - ]

  • If the ECM has been struck or dropped, replace it.
  • Perform Vehicle Identification Number (VIN) registration when replacing the ECM.

    Refer to REGISTRATION [04/2018 - ]

scientia non olet · About LEMON Manuals