Typical Enabling Conditions

WARNING: This page is about a different variant/trim than selected.

C13C1, C13CA, C14F2 AND C14FB

Monitor runs whenever the following DTCs are not stored	None
Both of the following conditions are met	-
Serial communication with high side IC	Valid
Solenoid low side operating	On

C13C2, C13CB, C14F3 AND C14FC (CASE 1)

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	-
Power supply for linear solenoid	Higher than 9.13 V
Command to main relay	On
Main relay	On
Serial communication with high side IC	Valid
Solenoid low side operating	On
Current	Less than 2.3 A
Difference in present target current and previous target current	0.2 A or less
Output duty cycle	Higher than 0%
Difference in present power supply voltage for linear solenoid and previous power supply voltage for linear solenoid	1 V or less
Solenoid current correction coefficient learning	Complete
Current monitor	Normal

C13C2, C13CB, C14F3 AND C14FC (CASE 2)

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	A, B, C, D, E, F, G, H, I and J
A. Power supply for linear solenoid	Higher than 9.13 V
B. Command to main relay	On
C. Main relay	On
D. Serial communication with high side IC	Valid
E. Solenoid low side operating	On
F. Current	Less than 2.3 A
G. Difference in present target current and previous target current	0.2 A or less
H. Output duty cycle	Higher than 0%
I. Current monitor	Normal
J. Either of the following conditions is met	-
Difference in present power supply voltage for linear solenoid and previous power supply voltage for linear solenoid	Higher than 1 V
Solenoid current correction coefficient learning	Not complete

C13C2, C13CB, C14F3 AND C14FC (CASE 3)

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	-
Command to main relay	On
Main relay	On
Solenoid low side operating	On
Serial communication with high side IC	Valid
Output duty cycle	0%
Current monitor	Normal
Current	Less than 0.2 A

C13C3, C13CC, C14F4 AND C14FD (CASE 1)

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	-
Power supply for linear solenoid	Less than 16 V
Serial communication with high side IC	Valid
Solenoid low side operating	On
Difference in present target current and previous target current	0.2 A or less
Difference in present power supply voltage for linear solenoid and previous power supply voltage for linear solenoid	1 V or less
Solenoid current correction coefficient learning	Complete
Current monitor	Normal

C13C3, C13CC, C14F4 AND C14FD (CASE 2)

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	A, B, C, D, E and F
A. Power supply for linear solenoid	Less than 16 V
B. Serial communication with high side IC	Valid
C. Solenoid low side operating	On
D. Difference in present target current and previous target current	0.2 A or less
E. Current monitor	Normal
F. Either of the following conditions is met	-
Difference in present power supply voltage for linear solenoid and previous power supply voltage for linear solenoid	Higher than 1 V
Solenoid current correction coefficient learning	Not complete

C13C3, C13CC, C14F4 AND C14FD (CASE 3)

Monitor runs whenever the following DTCs are not stored	None
All of the following conditions are met	-
Solenoid low side operating	On
Output duty cycle	0%
Current monitor	Normal

C13C3, C13CC, C14F4 AND C14FD (CASE 4)

Monitor runs whenever the following DTCs are not stored	None
Both of the following conditions are met	-
Serial communication with high side IC	Valid
Current monitor power supply	Higher than 1.09 V, and less than 1.24 V