LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> 4Runner TRD Pro >> Repair and Diagnosis >> External Pages >> Different car >> Section 2 (Front Bumper (W/ Intuitive Parking Assist System) - Service Information) >> FRONT BUMPER (w/ Intuitive Parking Assist System) >> Removal [08/2019 - 08/2021] >> Procedure

Removal [08/2019 - 08/2021]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2021 Toyota 4Runner, 2020 Toyota 4Runner, 2019 Toyota 4Runner, 2018 Toyota 4Runner, and 2017 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE UPPER RADIATOR SUPPORT SEAL 

    Refer to PROCEDURE - Step 18

  2. REMOVE FRONT BUMPER COVER 
    1. Apply protective tape as shown in the illustration.
      GTY889360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
    2. Remove the 3 screws.
      GTY924778Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 4 screws and 2 bolts.
      GTY924777Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 3 bolts.
      GTY945293Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 6 clips.
      GTY945292Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disengage the 7 claws as shown in the illustration.

      HINT: 

      Use the same procedure for the RH side and LH side.

      GTY845001Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    7. Disconnect the 3 connectors.
    8. Remove the front bumper cover.
  3. REMOVE UPPER CENTER FRONT BUMPER RETAINER 

    Refer to PROCEDURE - Step 11

  4. REMOVE COOL AIR INTAKE DUCT (for 4WD) 
    1. Remove the 4 clips and cool air intake duct.
      GTY442486Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FRONT BUMPER LOWER COVER 
    1. Remove the clip.
      GTY437818Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 4 bolts and front lower bumper cover.
  6. REMOVE AIR INTAKE DUCT LH 
    1. Remove the clip and bolt.
      GTY706113Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 screws and air intake duct LH.
  7. REMOVE AIR INTAKE DUCT RH 

    HINT: 

    Use the same procedure as for the LH side.

  8. REMOVE RADIATOR SIDE DEFLECTOR LH 

    Refer to PROCEDURE - Step 13

  9. REMOVE RADIATOR SIDE DEFLECTOR RH 

    Refer to PROCEDURE - Step 12

  10. REMOVE FRONT BUMPER ENERGY ABSORBER 

    Refer to PROCEDURE - Step 7 [08/2019 - 08/2020] , or refer to PROCEDURE - Step 7 [08/2020 - 08/2021]

  11. REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY 
    1. Remove the screw, 6 nuts and front bumper reinforcement sub-assembly.
      GTY437822Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE NO. 2 FRONT BUMPER EXTENSION SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 9 [08/2019 - 08/2020] , or refer to PROCEDURE - Step 9 [08/2020 - 08/2021]

  13. REMOVE NO. 2 FRONT BUMPER EXTENSION SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  14. REMOVE FRONT BUMPER SIDE SUPPORT LH 

    Refer to PROCEDURE - Step 11 [08/2019 - 08/2020] , or refer to PROCEDURE - Step 11 [08/2020 - 08/2021]

  15. REMOVE FRONT BUMPER SIDE SUPPORT RH 

    HINT: 

    Use the same procedure as for the LH side.

  16. REMOVE FRONT BUMPER BRACKET SUB-ASSEMBLY LH 

    Refer to PROCEDURE - Step 13 [08/2019 - 08/2020] , or refer to PROCEDURE - Step 13 [08/2020 - 08/2021]

  17. REMOVE FRONT BUMPER BRACKET SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

scientia non olet · About LEMON Manuals