LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> 4Runner TRD Pro >> Repair and Diagnosis >> External Pages >> Different car >> Section 2 (Front Bumper (W/ Intuitive Parking Assist System) - Service Information) >> FRONT BUMPER (w/ Intuitive Parking Assist System) >> Reassembly [08/2020 - 08/2021] >> Procedure

Reassembly [08/2020 - 08/2021]: Procedure

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2021 Toyota 4Runner, 2020 Toyota 4Runner, 2019 Toyota 4Runner, 2018 Toyota 4Runner, and 2017 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL FOG LIGHT ASSEMBLY LH 

    Refer to PROCEDURE - Step 1

  2. INSTALL FOG LIGHT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  3. INSTALL FRONT BUMPER MOULDING SUB-ASSEMBLY 
    1. Attach the 4 claws and 12 guides to install the front bumper moulding sub-assembly.
    2. Install the 15 outside moulding retainers and 4 screws.
  4. INSTALL FRONT BUMPER SIDE MOULDING SUB-ASSEMBLY LH 
    1. Attach the 2 claws and guide to install the front bumper side moulding sub-assembly LH.
    2. Install the 2 screws and 3 outside moulding retainers.
  5. INSTALL FRONT BUMPER SIDE MOULDING SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  6. INSTALL FRONT BUMPER REINFORCEMENT STOPPER RH (for RH Side) 
    1. Attach the 3 claws to install the front bumper reinforcement stopper RH.
  7. INSTALL NO. 2 RADIATOR GRILLE MOULDING 
    1. Attach the 4 claws to install the No. 2 radiator grille moulding.
    2. Install the 2 outside moulding retainers and 4 screws.
  8. INSTALL FRONT BUMPER LOWER SIDE SUPPORT LH 
    1. Attach the 5 claws.
    2. Install the front bumper lower side support LH with the 2 clips.
  9. INSTALL FRONT BUMPER LOWER SIDE SUPPORT RH 

    HINT: 

    Use the same procedure as for the LH side.

  10. INSTALL FRONT BUMPER SIDE MOULDING LH 
    1. Attach the claw to install the front bumper side moulding LH.
    2. Install the 2 outside moulding retainers.
  11. INSTALL FRONT BUMPER SIDE MOULDING RH 

    HINT: 

    Use the same procedure as for the LH side.

  12. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ License Plate Bracket) 
    1. Install the front bumper extension mounting bracket with the 2 screws.
  13. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER 

    Refer to PROCEDURE - Step 1

  14. INSTALL ULTRASONIC SENSOR CLIP 

    Refer to PROCEDURE - Step 2

  15. INSTALL NO. 1 ULTRASONIC SENSOR 

    Refer to PROCEDURE - Step 3

  16. INSTALL NO. 2 ENGINE ROOM WIRE 
    1. Attach the 9 clamps.
    2. Connect each connector and install the No. 2 engine room wire.
  17. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY 

    Refer to INSTALLATION [08/2019 - 08/2021]

  18. INSTALL RADIATOR GRILLE 

    Refer to PROCEDURE - Step 2

scientia non olet · About LEMON Manuals