LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Venza XLE >> Repair and Diagnosis >> Restraints >> Air Bag, SRS >> Airbag System - Diagnostic Codes (4 Of 4) & Symptom Tests >> Airbag System >> DTC B1875-13: Passenger Seat Cushion Airbag Squib Circuit Open [07/2020 - ] >> Procedure

DTC B1875-13: Passenger Seat Cushion Airbag Squib Circuit Open [07/2020 - ]: Procedure

  1. CHECK DTC 
    1. Turn the ignition switch to ON, and wait for at least 60 seconds.
    2. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

    3. Turn the ignition switch off.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.
    5. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Proceed to
      DTC B1875-13 is output
      DTC B1875-13 is not output

    Result: 

    DTC B1875-13 is not output 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2020 - ] 

    Result: 

    DTC B1875-13 is output 

    See step  2

  2. CHECK CONNECTION OF CONNECTORS 
    1. Turn the ignition switch off.
    2. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    3. Check that the connectors are properly connected to the front seat cushion airbag assembly RH and airbag sensor assembly.

      OK

      The connectors are properly connected.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    CONNECT CONNECTORS PROPERLY 

    Result: 

    OK 

    See step  3

  3. CHECK CONNECTORS 
    1. Disconnect the airbag sensor assembly connector.
      GTY972907Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Cushion Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Disconnect the front seat cushion airbag assembly RH connector.
    3. Check that the terminals of the connectors are not deformed or damaged.

      OK

      The terminals are not deformed or damaged.

    4. Check that the short springs of the activation prevention mechanism of the wire harness connector are not deformed or damaged.

      OK

      The short springs are not deformed or damaged.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK FRONT SEAT CUSHION AIRBAG ASSEMBLY RH 
    1. Connect the airbag sensor assembly connector.
      GTY1018653Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Cushion Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *4 SST
      *a Front view of wire harness connector
      (to Front Seat Cushion Airbag Assembly RH)
    2. Connect SST (resistance: 2.1 Ω) to connector C.
      WARNING:

      Never connect the tester to the front seat cushion airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.

      NOTE:
      • Do not forcibly insert SST into the terminals of the connector when connecting SST.
      • Insert SST straight into the terminals of the connector.
      • SST: 09843-18061 
    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.
    5. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

    6. Turn the ignition switch off.
    7. Turn the ignition switch to ON, and wait for at least 60 seconds.
    8. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Proceed to
      DTC B1875-13 is not output
      DTC B1875-13 is output

      HINT: 

      Codes other than DTC B1875-13 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.
    10. Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
    11. Disconnect SST from connector C.

    Result: 

    DTC B1875-13 is not output 

    REPLACE FRONT SEAT CUSHION AIRBAG ASSEMBLY RH. Refer to  REMOVAL [07/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - ] 

    Result: 

    DTC B1875-13 is output 

    See step  5

  5. CHECK HARNESS AND CONNECTOR 
    1. Disconnect the airbag sensor assembly connector.
      GTY1018668Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Cushion Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
      *a Front view of wire harness connector
      (to Front Seat Cushion Airbag Assembly RH)
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K18-1 (FCP-) - K18-2 (FCP+) Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK DTC 
    1. Connect the airbag sensor assembly connector.
      GTY972921Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Seat Cushion Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 Wire Harness
    2. Connect the front seat cushion airbag assembly RH connector.
    3. Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
    4. Turn the ignition switch to ON, and wait for at least 60 seconds.
    5. Clear the DTCs stored in memory.

      Body Electrical > SRS Airbag > Clear DTCs 

    6. Turn the ignition switch off.
    7. Turn the ignition switch to ON, and wait for at least 60 seconds.
    8. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Proceed to
      DTC B1875-13 is not output
      DTC B1875-13 is output

      HINT: 

      Codes other than DTC B1875-13 may be output at this time, but they are not related to this check.

    Result: 

    DTC B1875-13 is not output 

    USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [07/2020 - ] 

    Result: 

    DTC B1875-13 is output 

    REPLACE AIRBAG SENSOR ASSEMBLY. Refer to  REMOVAL [07/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - ] 

scientia non olet · About LEMON Manuals