LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Venza LE >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System (For 12.3 Inch Display) - Diagnostic Codes & Symptom Tests >> METER / GAUGE SYSTEM (for 12.3 Inch Display) >> DTC B1507-18: Turn Signal Light Circuit Current Below Threshold [10/2022 - ] >> Procedure

DTC B1507-18: Turn Signal Light Circuit Current Below Threshold [10/2022 - ]: Procedure

  1. CHECK SYMPTOMS 
    1. Check the problem symptoms.

      Result

      Result Proceed to
      LH side front turn signal light does not blink A
      LH side rear turn signal light does not blink B
      RH side front turn signal light does not blink C
      RH side rear turn signal light does not blink D

    Result: 

    B 

    See step  4

    Result: 

    C 

    See step  6

    Result: 

    D 

    See step  8

    Result: 

    A 

    See step  2

  2. CHECK LH SIDE FRONT TURN SIGNAL LIGHT 
    1. Remove the headlight assembly LH and RH.

      Refer to REMOVAL [07/2020 - ]

    2. Interchange the headlight assembly LH with RH and connect the connectors.
    3. Operate the turn signal switch and check that the LH side front turn signal light operates normally.

      Result

      Result Proceed to
      LH side front turn signal light operates normally A
      Problem symptoms do not change
      (LH side front turn signal light does not blink)      		 B

    Result: 

    A 

    REPLACE HEADLIGHT ASSEMBLY LH. Refer to  REMOVAL [07/2020 - ] 

    Result: 

    B 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the A95 headlight assembly LH connector.
    2. Disconnect the E140 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A95-2 (B) - E140-5 (LL) Always Below 1 Ω
      A95-6 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  4. INSPECT REAR TURN SIGNAL LIGHT LED LH 

    Refer to INSPECTION [07/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR TURN SIGNAL LIGHT LED LH. Refer to  DISASSEMBLY [07/2020 - ] 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (REAR TURN SIGNAL LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the E140 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      S6-2 (B) - E140-22 (TRNL) Always Below 1 Ω
      S6-1 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK RH SIDE FRONT TURN SIGNAL LIGHT 
    1. Remove the headlight assembly RH and LH.

      Refer to REMOVAL [07/2020 - ]

    2. Interchange the headlight assembly RH with LH and connect the connectors.
    3. Operate the turn signal switch and check that the RH side front turn signal light operates normally.

      Result

      Result Proceed to
      RH side front turn signal light operates normally A
      Problem symptoms do not change
      (RH side front turn signal light does not blink)      		 B

    Result: 

    A 

    REPLACE HEADLIGHT ASSEMBLY RH. Refer to  REMOVAL [07/2020 - ] 

    Result: 

    B 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the A94 headlight assembly RH connector.
    2. Disconnect the E140 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      A94-2 (B) - E140-6 (LR) Always Below 1 Ω
      A94-6 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  8. INSPECT REAR TURN SIGNAL LIGHT LED RH 

    Refer to INSPECTION [07/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR TURN SIGNAL LIGHT LED RH. Refer to  DISASSEMBLY [07/2020 - ] 

    Result: 

    OK 

    See step  9

  9. CHECK HARNESS AND CONNECTOR (REAR TURN SIGNAL LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND) 
    1. Disconnect the E140 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      S5-2 (B) - E140-21 (TRNR) Always Below 1 Ω
      S5-1 (E) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals