LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Venza LE >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System (Except 12.3 Inch Display) - Diagnostics - Introduction >> METER / GAUGE SYSTEM (except 12.3 Inch Display) >> Customize Parameters [07/2020 - ] >> Customize Parameters [07/2020 - ]

Customize Parameters [07/2020 - ]

  1. CUSTOMIZE METER / GAUGE SYSTEM 
    NOTE:
    • When the customer requests a change in a function, first make sure that the function can be customized.
    • Be sure to make a note of the current settings before customizing.
    • When troubleshooting a function, first make sure that the function is set to the default setting.
    1. Customizing with the GTS
      1. Select the setting by referring to the table below.

        Warning 

        Tester Display Description Default Setting ECU
        Flasher Sound Volume Adjust Function to change the turn signal flasher buzzer sound volume Medium $02:Large,$00:Medium,$01:Small Combination meter assembly
        Proposal Services Function Function to change the suggestion function display setting ON $00:OFF,$01:Parked,$03:ON Main body ECU (Multiplex network body ECU)

        Display 

        Tester Display Description Default Setting ECU
        ODO Display Time After IG OFF Adjust Function to change the trip result display time after the ignition switch is turned off 30s $00:30s,$01:60s,$02:600s,$03:OFF Combination meter assembly
    2. Customizing with the multi-display
      1. Enter the following menus: MENU / Setup / Vehicle / Vehicle Customization.
      2. Select the setting by referring to the table below.
        Display Default Content Setting Relevant ECU
        Suggestion Function On Function to change the suggestion function display setting On/On (when the vehicle is stopped)/Off Main body ECU (Multiplex network body ECU)
    3. Customizing with the multi-information display
      1. Select the settings tab on the multi-information display.
      2. Select the setting by referring to the table below.
        NOTE:
        • When the cable is disconnected from the negative (-) auxiliary battery terminal, some of the settings will be reset. Therefore, it is necessary to make a note of each set value before disconnecting the cable.
        • As some values cannot be selected when the vehicle is being driven, perform the procedure with the vehicle stopped.

        HINT: 

        Depending on the specifications of the vehicle, some items may not be displayed.

        LTA

        Display Description Setting ECU
        "Lane Center" Lane centering function setting ON/OFF Forward recognition camera
        "Steering Assist" Steering assist function setting ON/OFF
        "Alert" Lane departure alert method setting "Steering vibration/buzzer"
        "Sensitivity" Lane departure alert timing level setting 2 levels
        "Sway Warning" Vehicle sway warning function setting ON/OFF
        "Sway Sensitivity" Sway warning sensitivity level setting 3 levels
        PCS

        Display Description Setting ECU
        - Pre-collision system setting ON/OFF Forward recognition camera
        "Sensitivity" Pre-collision system sensitivity level setting 3 levels
        BSM

        Display Description Setting ECU
        - Blind spot monitor system setting ON/OFF Blind spot monitor sensor LH (B)
        "Brightness" Outer rear view mirror indicator brightness level setting 2 levels
        "Sensitivity" Blind spot monitor system sensitivity level setting 4 levels
        PARKING ASSIST

        Display Description Setting ECU
        - Intuitive parking assist system setting ON/OFF Clearance warning ECU assembly
        "Volume" Clearance warning buzzer volume level setting 3 levels
        RCTA

        Display Description Setting ECU
        - RCTA function setting ON/OFF Blind spot monitor sensor LH (B)
        "Volume" RCTA buzzer (blind spot monitor buzzer) volume setting 3 levels
        PKSB

        Display Description Setting ECU
        - Parking support brake system setting ON/OFF Clearance warning ECU assembly
        "HUD MAIN"

        Display Description Setting ECU
        - Headup display system setting ON/OFF Meter mirror sub-assembly
        "HUD Brightness/Position" Brightness and position setting for headup display -
        "HUD Driving Support" "Tachometer Settings" Display setting for headup display "Blank/Hybrid System/Eco Indicator/Tachometer"
        "Navigation" Display setting for headup display ON/OFF
        "Driving Assist" Display setting for headup display ON/OFF
        "Compass" Display setting for headup display ON/OFF
        "Audio" Display setting for headup display ON/OFF
        "HUD Rotation" Headup display image calibration (rotation calibration) -
        RSA

        Display Description Setting ECU
        - Road sign assist system setting ON/OFF Forward recognition camera
        "Notification Method" "Above Speed Limit" Excess speed notification method setting "No Notification/Only Visual/Visual & Audio"
        "Overtaking" No overtaking notification method setting "No Notification/Only Visual/Visual & Haptic"
        "Others" Others traffic sign notification method setting "No Notification/Only Visual/Visual & Audio"
        "Notification Level" Excess speed notification level setting -5 to 10
        "VEHICLE SETTINGS"

        Display Description Setting ECU
        "PBD" "System Settings" Power back door system setting ON/OFF Multiplex network door ECU
        "Hands Free" Hands free power back door function setting ON/OFF
        "Opening Adjustment" Back door opening stop position setting when operated by power back door system 5 levels
        "Volume" Power back door buzzer volume level setting 3 levels
        "TPWS" "Setting Pressure" Tire inflation pressure display function setting - Tire pressure warning ECU and receiver
        "Identify Wheel" Tire inflation pressure display function setting -
        "Setting Unit" Tire inflation pressure display function setting "kPa/psi/bar"
        "Rear Seat Reminder" Rear seat reminder function setting ON/OFF Main body ECU (Multiplex network body ECU)
        "Scheduled Maintenance" Scheduled maintenance required reminder data reset Yes/No Combination meter assembly
        "Oil Maintenance" Engine oil maintenance required reminder data reset Yes/No ECM
        "SETTINGS" (FOR 4.2 INCH DISPLAY TYPE)

        Display Description Setting ECU
        "Language" Display language setting * Related ECUs
        "Units" Display units setting *
        Eco driving indicator light Eco driving indicator light display setting ON/OFF Combination meter assembly
        EV driving indicator light EV driving indicator light display setting ON/OFF
        Eco-friendly driving information tab "Hybrid System" "Eco Guidance" Eco acceleration guidance display setting ON/OFF
        "Fuel Economy" Displayed fuel economy display item setting "Trip Average/Total Average/Tank Average"
        Audio tab Audio tab display setting ON/OFF
        Vehicle information tab "Display Contents" "Energy Monitor" Energy monitor display setting ON/OFF
        "AWD" AWD system monitor display setting ON/OFF
        "Drive Info Type" Displayed drive information display item setting "Trip/Total"
        "Drive Info Items" Displayed drive information display item setting "Average Speed/Distance/Total Time"
        "Trip Summary" Current trip result display setting "Drive Info/Eco Score"
        "Pop-Up Display" "Pop-Up Display" Interrupt display setting ON/OFF Combination meter assembly
        "Telephone" Interrupt display setting ON/OFF
        "Audio Operation" Interrupt display setting ON/OFF
        "Volume Operation" Interrupt display setting ON/OFF
        "Voice Control" Interrupt display setting ON/OFF
        "Brightness" Interrupt display setting ON/OFF
        "MID OFF" Multi-information display off setting -
        "Default Settings" Reset the combination meter settings to the default setting Yes/No Related ECUs
        1. *: Varies according to the vehicle specification.
        "SETTINGS" (FOR 7 INCH DISPLAY TYPE)

        Display Description Setting ECU
        "Language" Display language setting * Related ECUs
        "Units" Display units setting *
        Eco driving indicator light Eco driving indicator light display setting ON/OFF Combination meter assembly
        EV driving indicator light EV driving indicator light display setting ON/OFF
        "Digital Speed" Digital speedometer display setting ON/OFF
        "Gadget Content" Displayed drive information display item setting "No Display/Average Speed/Distance/Total Time"
        "Drive Info Type" Displayed drive information display item setting "Trip/Total/Tank"
        "Pop-Up Display" "Pop-Up Display" Interrupt display setting ON/OFF Combination meter assembly
        "Telephone" Interrupt display setting ON/OFF
        "Audio Operation" Interrupt display setting ON/OFF
        "Volume Operation" Interrupt display setting ON/OFF
        "Voice Control" Interrupt display setting ON/OFF
        "Brightness" Interrupt display setting ON/OFF
        "MID OFF" Multi-information display off setting -
        "Default Settings" Reset the combination meter settings to the default setting Yes/No Related ECUs
        1. *: Varies according to the vehicle specification.
scientia non olet · About LEMON Manuals