LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Venza LE >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System (Except 12.3 Inch Display) - Diagnostic Codes & Symptom Tests >> METER / GAUGE SYSTEM (except 12.3 Inch Display) >> DTC B1500-13: Fuel Sender Circuit Open [07/2020 - ] >> Procedure

DTC B1500-13: Fuel Sender Circuit Open [07/2020 - ]: Procedure

  1. READ VALUE USING GTS 
    1. Read the Data List according to the display on the GTS.

      Body Electrical > Combination Meter > Data List 

      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Fuel Input Fuel level gauge output Min.: 0.00 L, Max.: 655.35 L or Unset
      • Fuel receiver gauge indicates F: 47.66 L
      • Fuel receiver gauge indicates 3/4: 37.58 L
      • Fuel receiver gauge indicates 1/2: 27.50 L
      • Fuel receiver gauge indicates 1/4: 13.75 L
      • Fuel receiver gauge indicates E: 5.50 L
      -

      Body Electrical > Combination Meter > Data List 

      Tester Display
      Fuel Input

      Result

      Result Proceed to
      Fuel level data can be displayed on the GTS A
      Fuel level data cannot be displayed on the GTS B

    Result: 

    A 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [07/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - ] 

    Result: 

    B 

    See step  2

  2. INSPECT FUEL SENDER GAUGE ASSEMBLY 

    Refer to INSPECTION [07/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE FUEL SENDER GAUGE ASSEMBLY. Refer to  REMOVAL [07/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - ] 

    Result: 

    OK 

    See step  3

  3. INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 
    GTY985670Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Component without harness connected
    (Fuel Suction Tube with Pump and Gauge Assembly)
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      L23-1 (FV) - A-3 Always Below 1 Ω
      L23-2 (FE) - A-2 Always Below 1 Ω
      L23-3 (FS) - A-1 Always Below 1 Ω
      L23-1 (FV) - L23-2 (FE)
      or
      A-3 - A-2
      Always 10 kΩ or higher
      L23-1 (FV) - L23-3 (FS)
      or
      A-3 - A-1
      Always 10 kΩ or higher
      L23-2 (FE) - L23-3 (FS)
      or
      A-2 - A-1
      Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY. Refer to  REMOVAL [07/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - ] 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the E17 combination meter assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      L23-1 (FV) -E17-15 (FV) Always Below 1 Ω
      L23-2 (FE) -E17-33 (FE&B) Always Below 1 Ω
      L23-3 (FS) -E17-14 (FR) Always Below 1 Ω
      L23-1 (FV) or E17-15 (FV) - Body ground Always 10 kΩ or higher
      L23-3 (FS) or E17-14 (FR) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [07/2020 - 10/2022]  , or refer to  REMOVAL [10/2022 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR