DTC C0500-1F: Left Front Wheel Speed Sensor Circuit Intermittent; DTC C0506-1F: Right Front Wheel Speed Sensor Circuit Intermittent [11/2018 - ]: Procedure

1. Remove the front speed sensor.

   Refer to REMOVAL [11/2018 - ]

2. Check the front speed sensor.

   OK

   The front speed sensor tip is free of oil and foreign matter.

   HINT: 

   If foreign matter of 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or more is adhered to the front speed sensor, this DTC may be stored.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  7

Result: 

OK 

See step  2

1. Remove the component with the front speed sensor rotor.

   Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

2. Check the front speed sensor rotor.

   OK

   The front speed sensor rotor is free of oil and foreign matter.

   HINT: 

   If foreign matter of 1 mm (0.03937 in.) x 1 mm (0.03937 in.) or more is adhered to the front speed sensor rotor, this DTC may be stored.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE FRONT SPEED SENSOR AND FRONT AXLE HUB SUB-ASSEMBLY 

for front speed sensor: Refer to REMOVAL [11/2018 - ]

for front speed sensor rotor (front axle hub sub-assembly): Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

NG 

See step  3

1. Clean the front speed sensor rotor.
   NOTE:

   Do not use parts cleaner when cleaning the front speed sensor rotor.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  4

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

   Chassis > Brake/EPB > Clear DTCs 

4. Press the DTC clear button.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  5

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

   Refer to TEST MODE PROCEDURE [11/2018 - ]

   Chassis > Brake/EPB > Utility 

   Tester Display
   Signal Check

   OK

   Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE FRONT SPEED SENSOR AND FRONT AXLE HUB SUB-ASSEMBLY 

for front speed sensor: Refer to REMOVAL [11/2018 - ]

for front speed sensor rotor (front axle hub sub-assembly): Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

Result: 

OK 

See step  6

1. Connect the Techstream to the DLC3.
2. Start the engine.
3. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
4. Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

   Chassis > Brake/EPB > Trouble Codes 

5. Check if the same DTC is output.

   Result

   Result	Proceed to
   C0500-1F and C0506-1F is not output	A
   C0500-1F and/or C0506-1F is output	B

Result: 

A 

END 

Result: 

B 

REPLACE FRONT SPEED SENSOR AND FRONT AXLE HUB SUB-ASSEMBLY 

for front speed sensor: Refer to REMOVAL [11/2018 - ]

for front speed sensor rotor (front axle hub sub-assembly): Refer to REMOVAL [11/2018 - 02/2019] , or refer to REMOVAL [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020] , or refer to REMOVAL [08/2020 - 12/2021] , or refer to REMOVAL [12/2021 - 10/2022] , or refer to REMOVAL [10/2022 - 10/2023] , or refer to REMOVAL [10/2023 - ]

1. Clean the front speed sensor.
   NOTE:

   When cleaning the front speed sensor, make sure to clean the installation hole before installation.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  8

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

   Chassis > Brake/EPB > Clear DTCs 

4. Press the DTC clear button.

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  9

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.

   Refer to TEST MODE PROCEDURE [11/2018 - ]

   Chassis > Brake/EPB > Utility 

   Tester Display
   Signal Check

   OK

   Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  2

Result: 

OK 

See step  10

1. Connect the Techstream to the DLC3.
2. Start the engine.
3. Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
4. Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.

   Chassis > Brake/EPB > Trouble Codes 

5. Check if the same DTC is output.

   Result

   Result	Proceed to
   C0500-1F and C0506-1F is not output	A
   C0500-1F and/or C0506-1F is output	B

Result: 

A 

END 

Result: 

B 

See step  2