Brake Hold Standby Indicator Light Circuit [11/2018 - 10/2022]: Procedure

1. If the brake hold standby indicator light does not illuminate even though the brake hold switch (integration control and panel assembly) is pushed, check that the brake hold function operation conditions are met.
   1. The driver door is closed.
   2. The driver seat belt is fastened.
   3. The system is normal.

   HINT: 

   If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

   • Brake system
   • Electric parking brake system

   Result

   Proceed to
   NEXT

Result: 

NEXT 

See step  2

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Enter the following menus: Chassis / Brake/EPB / Data List.

   Chassis > Brake/EPB > Data List 

   Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
   Brake Hold Ready	Brake hold control permission status	Not in stand-by mode / Stand-by mode	Not in stand-by mode: Brake hold function not operating (brake hold indicator not illuminated) Stand-by mode: Brake hold function stand-by state (brake hold indicator illuminated)	-

   Chassis > Brake/EPB > Data List 

   Tester Display
   Brake Hold Ready

4. All of the following brake hold operation conditions are met:
   1. The driver door is closed.
   2. The driver seat belt is fastened.
5. Check the brake hold standby indicator light and mode condition on the Techstream changes according to brake hold switch (integration control and panel assembly) operation.

   Standard

   Brake Hold Switch (Integration Control and Panel Assembly) Operation	Mode Condition Display	Brake Hold Standby Indicator Light
   Not pressed	Not in stand-by mode	Does not come on
   Pressing the brake hold switch (integration control and panel assembly)	Stand-by mode	Come on

   Result

   Result	Proceed to
   Indicator light and mode condition display do not change	A
   Mode condition display is normal, but indicator light does not change	B
   Indicator light and mode condition display are normal	C

Result: 

B 

INSPECT METER / GAUGE SYSTEM. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ] 

Result: 

C 

USE SIMULATION METHOD TO CHECK. Refer to  HOW TO PROCEED WITH TROUBLESHOOTING [11/2018 - ] 

Result: 

A 

See step  3

1. Inspect the brake hold switch (integration control and panel assembly).

   Refer to INSPECTION [11/2018 - ]

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPLACE INTEGRATION CONTROL AND PANEL ASSEMBLY. Refer to  REMOVAL [11/2018 - ] 

Result: 

OK 

See step  4

1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

   OK

   The connector is securely connected.

2. Disconnect the A39 skid control ECU (brake actuator assembly) connector.
3. Disconnect the G32 brake hold switch (integration control and panel assembly) connector.
4. Check both the connector case and the terminal for deformation and corrosion.

   OK

   No deformation or corrosion.

5. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G32-24 (+B) - A39-42 (EXI3)	Always	Below 1 Ω
   G32-24 (+B) or A39-42 (EXI3) - Body ground	Always	10 kΩ or higher
   G32-15 (E) - Body ground	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

Result: 

OK 

REPLACE BRAKE ACTUATOR ASSEMBLY. Refer to  REMOVAL [11/2018 - 10/2019]  , or refer to  REMOVAL [10/2019 - 08/2020]  , or refer to  REMOVAL [08/2020 - 10/2022] 

Result: 

NG 

REPAIR OR REPLACE HARNESS OR CONNECTOR