LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> RAV4 LE, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System - Diagnostic Codes (1 Of 2) >> Meter / Gauge System >> DTC B1500-13: Fuel Sender Circuit Open; DTC B1501-13: Sub Fuel Sender Circuit Open [11/2018 - 02/2019] >> Procedure

DTC B1500-13: Fuel Sender Circuit Open; DTC B1501-13: Sub Fuel Sender Circuit Open [11/2018 - 02/2019]: Procedure

  1. CHECK VEHICLE CONDITION 
    1. Check vehicle condition.

      Result

      Result Proceed to
      for Gasoline Model A
      for HV Model B

    Result: 

    B 

    See step  9

    Result: 

    A 

    See step  2

  2. CHECK FOR DTC 
    1. Check for DTCs

      Refer to DTC CHECK / CLEAR [11/2018 - ]

      Body Electrical > Combination Meter > Trouble Codes 

      Result

      Result Proceed to
      DTCs B1500-13 and B1501-13 are output A
      DTC B1500-13 is output B
      DTC B1501-13 is output C

    Result: 

    B 

    See step  4

    Result: 

    C 

    See step  7

    Result: 

    A 

    See step  3

  3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY) 
    1. Disconnect the G18 combination meter assembly connector.
    2. Disconnect the N27 fuel suction with pump and gauge tube assembly connector.
    3. Disconnect the M18 No. 2 fuel sender gauge assembly connector.
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      G18-24 (FE&B) - N27-2 (FE) Always Below 1 Ω
      G18-14 (FV) - N27-1 (FV) Always Below 1 Ω
      G18-24 (FE&B) or N27-2 (FE) - Other terminals and body ground Always 10 kΩ or higher
      G18-14 (FV) or N27-1 (FV) - Other terminals and body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [11/2018 - 10/2022]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  4. CHECK HARNESS AND CONNECTOR (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the N27 fuel suction with pump and gauge tube assembly connector.
    2. Disconnect the G18 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N27-3 (FS) - G18-31(FR) Always Below 1 Ω
      N27-2 (FE) - G18-24 (FE&B) Always Below 1 Ω
      N27-1 (FV) - G18-14 (FV) Always Below 1 Ω
      N27-3 (FS) or G18-31 (FR) - Other terminals and body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. INSPECT FUEL SENDER GAUGE ASSEMBLY 
    1. Remove the fuel sender gauge assembly.

      w/ Canister Pump Module:

      Refer to REMOVAL [11/2018 - 08/2020]

      w/o Canister Pump Module:

      Refer to REMOVAL [11/2018 - 08/2020]

    2. Inspect the fuel sender gauge assembly.

      w/ Canister Pump Module:

      Refer to INSPECTION [11/2018 - ]

      w/o Canister Pump Module:

      Refer to INSPECTION [11/2018 - 08/2020]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FUEL SENDER GAUGE ASSEMBLY 

    w/ Canister Pump Module:

    Refer to REMOVAL [11/2018 - 08/2020]

    w/o Canister Pump Module:

    Refer to REMOVAL [11/2018 - 08/2020]

    Result: 

    OK 

    See step  6

  6. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N27-1 (FV) - A-3 Always Below 1 Ω
      N27-2 (FE) - A-2 Always Below 1 Ω
      N27-3 (FS) - A-1 Always Below 1 Ω
      GTY869182Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Fuel Suction with Pump and Gauge Tube Assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [11/2018 - 10/2022]

    Result: 

    NG 

    REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 

    w/ Canister Pump Module:

    Refer to REMOVAL [11/2018 - 08/2020]

    w/o Canister Pump Module:

    Refer to REMOVAL [11/2018 - 08/2020]

  7. CHECK HARNESS AND CONNECTOR (NO. 2 FUEL SENDER GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the M18 No. 2 fuel sender gauge assembly connector.
    2. Disconnect the G18 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M18-3 (FR) - G18-13(FR2) Always Below 1 Ω
      M18-2 (FE) - G18-24 (FE&B) Always Below 1 Ω
      M18-1 (FV) - G18-14 (FV) Always Below 1 Ω
      M18-3 (FR) or G18-13(FR2) - Other terminals and body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY 
    1. Remove the No. 2 fuel sender gauge assembly.

      w/ Canister Pump Module:

      Refer to REMOVAL [11/2018 - 08/2020]

      w/o Canister Pump Module:

      Refer to REMOVAL [11/2018 - 08/2020]

    2. Inspect the No. 2 fuel sender gauge assembly.

      w/ Canister Pump Module:

      Refer to INSPECTION [11/2018 - ]

      w/o Canister Pump Module:

      Refer to INSPECTION [11/2018 - 08/2020]

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [11/2018 - 10/2022]

    Result: 

    NG 

    REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY 

    w/ Canister Pump Module:

    Refer to REMOVAL [11/2018 - 08/2020]

    w/o Canister Pump Module:

    Refer to REMOVAL [11/2018 - 08/2020]

  9. CHECK HARNESS AND CONNECTOR (FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY - COMBINATION METER ASSEMBLY) 
    1. Disconnect the N47 fuel suction with pump and gauge tube assembly connector.
    2. Disconnect the G18 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N47-3 (FS) - G18-31(FR) Always Below 1 Ω
      N47-2 (FE) - G18-24 (FE&B) Always Below 1 Ω
      N47-1 (FV) - G18-14 (FV) Always Below 1 Ω
      N47-3 (FS) or G18-31 (FR) - Other terminals and body ground Always 10 kΩ or higher
      N47-2 (FE) or G18-24 (FE&B) - Other terminals and body ground Always 10 kΩ or higher
      N47-1 (FV) or G18-14 (FV) - Other terminals and body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  10

  10. INSPECT FUEL SENDER GAUGE ASSEMBLY 
    1. Remove the fuel sender gauge assembly.

      Refer to REMOVAL [11/2018 - 08/2020]

    2. Inspect the fuel sender gauge assembly.

      Refer to INSPECTION [11/2018 - 08/2020]

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE FUEL SENDER GAUGE ASSEMBLY 

    Refer to REMOVAL [11/2018 - 08/2020]

    Result: 

    OK 

    See step  11

  11. INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 
    GTY869181Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Component without harness connected
    (Fuel Suction with Pump and Gauge Tube Assembly)
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      N47-1 (FV) - A-3 Always Below 1 Ω
      N47-2 (FE) - A-2 Always Below 1 Ω
      N47-3 (FS) - A-1 Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY 

    Refer to REMOVAL [11/2018 - 10/2022]

    Result: 

    NG 

    REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY 

    Refer to REMOVAL [11/2018 - 08/2020]

scientia non olet · About LEMON Manuals