DTC B1321-87: Lost Communication with EMV Missing Message [10/2022 - ]: Procedure

1. Disconnect the cable from the negative (-) auxiliary battery terminal.
2. Disconnect the G18*1 or G140*2 combination meter assembly connector.
   1. *1: for 7 Inch Multi-information Display Type
   2. *2: for 12.3 Inch Multi-information Display Type
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   FOR 7 INCH MULTI-INFORMATION DISPLAY TYPE
   
   

   Tester Connection	Condition	Specified Condition
   G18-27 (MSCH) - G18-10 (MSCL)	Cable disconnected from negative (-) auxiliary battery terminal	108 to 132 Ω
   G18-27 (MSCH) - G114-4 (CG)	Cable disconnected from negative (-) auxiliary battery terminal	200 Ω or higher
   G18-10 (MSCL) - G114-4 (CG)	Cable disconnected from negative (-) auxiliary battery terminal	200 Ω or higher
   G18-27 (MSCH) - G114-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher
   G18-10 (MSCL) - G114-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher

   FOR 12.3 INCH MULTI-INFORMATION DISPLAY TYPE
   
   

   Tester Connection	Condition	Specified Condition
   G140-32 (MSCH) - G140-15 (MSCL)	Cable disconnected from negative (-) auxiliary battery terminal	108 to 132 Ω
   G140-32 (MSCH) - G114-4 (CG)	Cable disconnected from negative (-) auxiliary battery terminal	200 Ω or higher
   G140-15 (MSCL) - G114-4 (CG)	Cable disconnected from negative (-) auxiliary battery terminal	200 Ω or higher
   G140-32 (MSCH) - G114-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher
   G140-15 (MSCL) - G114-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

See step  3

Result: 

OK 

See step  2

1. Replace the combination meter assembly.

   Refer to REMOVAL [10/2022 - ]

2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [11/2018 - ]

   Body Electrical > Combination Meter > Clear DTCs 

3. Make sure that the DTC detection conditions are met.

   HINT: 

   If the detection conditions are not met, the system cannot detect the malfunction.

4. Recheck for DTCs and check that no DTCs are output.

   Refer to DTC CHECK / CLEAR [11/2018 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   OK

   DTC B1321-87 is not output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE) 

Result: 

NG 

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

1. Reconnect the G18*1 or G140*2 combination meter assembly connector.
   1. *1: for 7 Inch Multi-information Display Type
   2. *2: for 12.3 Inch Multi-information Display Type
2. Disconnect the G138 radio and display receiver assembly connector.
3. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   G138-5 (CNH1) - G138-6 (CNL1)	Cable disconnected from negative (-) auxiliary battery terminal	108 to 132 Ω
   G138-5 (CNH1) - G114-4 (CG)	Cable disconnected from negative (-) auxiliary battery terminal	200 Ω or higher
   G138-6 (CNL1) - G114-4 (CG)	Cable disconnected from negative (-) auxiliary battery terminal	200 Ω or higher
   G138-5 (CNH1) - G114-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher
   G138-6 (CNL1) - G114-16 (BAT)	Cable disconnected from negative (-) auxiliary battery terminal	6 kΩ or higher

   Result

   Proceed to
   OK
   NG

Result: 

NG 

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR 

Result: 

OK 

See step  4

1. Replace the combination meter assembly.

   Refer to REMOVAL [10/2022 - ]

2. Clear the DTCs.

   Refer to DTC CHECK / CLEAR [11/2018 - ]

   Body Electrical > Combination Meter > Clear DTCs 

3. Make sure that the DTC detection conditions are met.

   HINT: 

   If the detection conditions are not met, the system cannot detect the malfunction.

4. Recheck for DTCs and check that no DTCs are output.

   Refer to DTC CHECK / CLEAR [11/2018 - ]

   Body Electrical > Combination Meter > Trouble Codes 

   OK

   DTC B1321-87 is not output.

   Result

   Proceed to
   OK
   NG

Result: 

OK 

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE) 

Result: 

NG 

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [10/2022 - ]