LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Prius Prime Limited >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information >> Roof Headlining >> Removal [07/2020 - ] >> Procedure

Removal [07/2020 - ]: Procedure

  1. PRECAUTION 
    WARNING:

    Be sure to read Precaution thoroughly before servicing.

    Refer to PRECAUTION [07/2020 - ]

    GTY607029Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Refer to PRECAUTION [05/2019 - ]

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 2

    WARNING:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    GTY581108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE TONNEAU COVER ASSEMBLY 
    1. Remove the tonneau cover assembly.
  4. REMOVE REAR NO. 2 FLOOR BOARD 
    1. Remove the rear No. 2 floor board.
  5. REMOVE REAR NO. 4 FLOOR BOARD 
    1. Remove the rear No. 4 floor board.
  6. REMOVE REAR NO. 3 FLOOR BOARD 
    1. Remove the rear No. 3 floor board.
  7. REMOVE REAR NO. 1 FLOOR BOARD 
    1. Using a clip remover, remove the 4 clips.
      GTY737486Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 guides to remove the rear No. 1 floor board.
  8. REMOVE DECK FLOOR BOX LH 
    1. Disengage the 2 claws and 5 guides to remove the deck floor box LH.
      GTY716385Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE DECK FLOOR BOX RH 
    1. Disengage the 2 claws and 4 guides to remove the deck floor box RH.
      GTY716387Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE DECK TRIM SERVICE HOLE COVER 

    Refer to PROCEDURE - Step 2

  11. REMOVE REAR DECK TRIM COVER 
    1. Remove the bolt.
      GTY716384Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 4 clips to remove the rear deck trim cover.
  12. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. Disengage the claw as shown in the illustration.
      GTY600989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction

      HINT: 

      Use the same procedure for the front side and rear side.

    2. Disengage the 6 claws and 2 guides to remove the front door scuff plate LH as shown in the illustration.
      GTY581862Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  13. REMOVE COWL SIDE TRIM BOARD LH 
    1. Remove the clip.
      GTY604947Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disengage the 2 clips to remove the cowl side trim board LH as shown in the illustration.
  14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 3

  15. REMOVE FRONT PILLAR GARNISH LH 
    1. Apply protective tape around the front pillar garnish LH as shown in the illustration.
      GTY586028Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      HINT: 

      Let the front pillar garnish LH hang from the front pillar garnish clip.

      GTY539722Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Pillar Garnish Clip
      Place Hand Here
      Remove in this Direction
    3. While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
      GTY596053Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Pillar Garnish Clip
      Remove in this Direction
      NOTE:
      • The front pillar garnish clip is reusable if it is not damaged.
      • If the front pillar garnish clip is damaged, replace it with a new one.

      HINT: 

      When the front pillar garnish clip cannot be disengaged easily:

      1. While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.
        GTY710621Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Move in this Direction
      2. While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.
        GTY721720Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Pull in this Direction
    4. Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
      GTY556323Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Protect the curtain shield airbag assembly LH.
      GTY561192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      *b Adhesive Tape
      1. Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.
        NOTE:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  16. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Disengage the claw as shown in the illustration.
      GTY607184Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.
      GTY541514Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 2

  18. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) 

    Refer to PROCEDURE - Step 7

  19. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 8

  20. REMOVE LOWER CENTER PILLAR GARNISH LH 
    1. Pull the lower center pillar garnish LH in the directions indicated by the arrows (1) shown in the illustration to disengage the 2 claws (A).
      GTY601098Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw (A)
      *b Claw (B)
      Place Hand Here
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. Pull the lower center pillar garnish LH in the direction indicated by the arrow (2) shown in the illustration to disengage the 2 claws (B).
    3. Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.
      GTY591539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
  21. REMOVE CENTER PILLAR GARNISH ASSEMBLY LH 
    1. Using a clip remover, remove the 2 clips.
      GTY603763Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide as shown in the illustration.
      GTY586466Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Disengage the clip and 2 guides to remove the center pillar garnish assembly LH as shown in the illustration.
      GTY606989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
  22. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  23. REMOVE COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  24. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  25. REMOVE FRONT PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  26. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  27. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  28. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  29. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  30. REMOVE LOWER CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  31. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  32. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [05/2019 - ]

  33. REMOVE REAR UNDER SIDE COVER LH 
    1. Remove the 2 clips.
      GTY719909Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.
  34. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH 
    1. Loosen the bolt to remove the rear seatback hinge sub-assembly LH.
      GTY716390Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE REAR PILLAR COVER LH 
    1. Disengage the 7 claws and guide to remove the rear pillar cover LH as shown in the illustration.
      GTY1012183Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  36. REMOVE REAR SEAT SIDE GARNISH LH 
    1. Disconnect the rear seat side airbag assembly connector.
      NOTE:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
        GTY432307Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a White Housing Lock
        *b Yellow CPA
        Slide
      2. Push down the white housing lock again and disconnect the connector.
        NOTE:

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    2. Remove the 2 bolts.
      GTY1013306Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the claw as shown in the illustration.
      GTY1011260Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    4. Disengage the 2 clips and guide to remove the rear seat side garnish LH as shown in the illustration.
      GTY1011832Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  37. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for LH Side) 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the No. 1 tonneau cover holder cap as shown in the illustration.
      GTY548151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
  38. REMOVE TONNEAU COVER HOOK A (for LH Side) 
    1. Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the tonneau cover hook A as shown in the illustration.
      GTY561730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protective Tape
      Insert Screwdriver Here
      Remove in this Direction
  39. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. Lower the No. 2 luggage compartment trim hook as shown in the illustration.
      GTY727270Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 2 Luggage Compartment Trim Hook
    2. Using a screwdriver with its tip wrapped with protective tape, disengage the clip as shown in the illustration.
      GTY569633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 2 Luggage Compartment Trim Hook
      *a Protective Tape
      *b Hole (A)
      *c Clip
      Insert Screwdriver Here
      Remove in this Direction

      HINT: 

      Insert the screwdriver into the hole (A).

    3. Remove the 2 screws.
      GTY722931Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Screw
      Clip
    4. Using a clip remover, remove the clip.
    5. Disengage the 5 claws, 2 clips and guide to remove the deck trim side panel assembly LH as shown in the illustration.
      GTY739035Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  40. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH 
    1. Disengage the 5 clips as shown in the illustration to remove the roof side inner garnish assembly LH.
      GTY593460Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  41. REMOVE REAR UNDER SIDE COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  42. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  43. REMOVE REAR PILLAR COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  44. REMOVE REAR SEAT SIDE GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  45. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  46. REMOVE TONNEAU COVER HOOK A (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  47. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  48. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  49. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  50. REMOVE ROOF CONSOLE BOX ASSEMBLY 

    Refer to PROCEDURE - Step 1

  51. REMOVE NO. 1 ROOM LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  52. REMOVE SENSOR COVER (w/ Humidity Sensor) 

    Refer to PROCEDURE - Step 1

  53. REMOVE AIR CONDITIONING THERMISTOR ASSEMBLY (w/ Humidity Sensor) 

    Refer to PROCEDURE - Step 3

  54. REMOVE RAIN SENSOR COVER (w/ Rain Sensor) 

    Refer to PROCEDURE - Step 1

  55. REMOVE RAIN SENSOR (w/ Rain Sensor) 

    Refer to PROCEDURE - Step 2

  56. REMOVE NO. 2 FORWARD RECOGNITION COVER 

    Refer to PROCEDURE - Step 1

  57. REMOVE NO. 1 FORWARD RECOGNITION COVER 

    Refer to PROCEDURE - Step 2

  58. REMOVE ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for all assist grip assemblies.

    1. Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
      • SST: 09813-00010 
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      GTY844650Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cutout
    2. Pull SST as shown in the illustration to disengage the claw.
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

      GTY934126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 30 to 45°
      Pull in this Direction

      HINT: 

      • Use the same procedure for the claw on the other side of the assist grip cover LH.
      • Use the same procedure for the LH side and RH side.
    3. Remove the assist grip cover LH.

      HINT: 

      Use the same procedure for the LH side and RH side.

    4. Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.
      GTY561348Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Remove the 2 clips from the vehicle body.
  59. REMOVE REAR ASSIST GRIP ASSEMBLY LH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  60. REMOVE REAR ASSIST GRIP ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  61. REMOVE VISOR BRACKET COVER (for LH Side) 
    1. Using a molding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover.
      GTY578687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Insert Molding Remover Here
  62. REMOVE VISOR ASSEMBLY LH 
    1. for "TORX" Screw:
      GTY552554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using a T25 "TORX" socket wrench, remove the 2 screws.
    2. except "TORX" Screw:
      1. Remove the 2 screws.
    3. Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.
      GTY603553Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Visor Holder LH
      Remove in this Direction (1)
      Remove in this Direction (2)
    4. Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.
  63. REMOVE VISOR HOLDER LH 
    1. Turn the visor holder LH approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.
      GTY602037Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 45°
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. Disengage the 2 claws to remove the base of the visor holder LH.
  64. REMOVE VISOR BRACKET COVER (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  65. REMOVE VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  66. REMOVE VISOR HOLDER RH 

    HINT: 

    Use the same procedure as for the LH side.

  67. REMOVE ROOF HEADLINING ASSEMBLY 
    1. for Windshield Glass Side:
      1. Disconnect each connector.
    2. for Front Pillar LH Side:
      1. Remove the protective cover.
      2. Using a clip remover, disengage the 4 clamps.
        GTY552376Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Disconnect the 2 connectors.
      4. Install the protective cover.
    3. for Front Pillar RH Side:
      1. Remove the protective cover.
      2. Using a clip remover, disengage the 3 clamps.
        GTY696875Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *A w/ Satellite Radio
      3. Disconnect each connector.
      4. Install the protective cover.
    4. for Rear Pillar RH Side:
      GTY552525Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disconnect the 2 connectors.
    5. Using a clip remover, remove the 3 clips.
      GTY712952Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.
      NOTE:

      Do not damage the roof headlining assembly or vehicle interior.

      GTY704730Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
scientia non olet · About LEMON Manuals