LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Mirai XLE >> Repair and Diagnosis >> Suspension >> Front Suspension >> Suspension System (Front) - Service Information (1 Of 2) >> Front Upper Suspension Arm >> Removal [11/2021 - 12/2022] >> Procedure

Removal [11/2021 - 12/2022]: Procedure

  1. REMOVE FRONT WHEEL 

    Refer to REMOVAL [11/2020 - 12/2023]

  2. DISCONNECT STEERING KNUCKLE LH 
    1. GTY980520Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Block *b Jack
      *c SST (Spacer B) *d 1 mm (0.0394 in.)
      *e Spacer *f Center Nut
      *g Body *h Claw
      *i Parallel *j String
      1. Support the front suspension lower arm assembly LH using a jack and wooden block.
      2. Remove the 2 clips and 2 nuts.
      3. Install 2 SST (spacer B) onto the front upper No. 1 suspension arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.
        • SST: 09960-20010 
          1. 09961-02060
        NOTE:
        • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.
        • As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.
      4. Using SST, disconnect the steering knuckle assembly LH from the front upper No. 1 suspension arm assembly LH.
        • SST: 09960-20010 
          1. 09961-02010
        NOTE:
        • Apply molybdenum grease to the bolt threads and end of the SST bolt.
        • Do not damage the dust cover.
        • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.
        • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
      5. Install 2 SST (spacer B) onto the front upper No. 2 suspension arm assembly LH so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.
        • SST: 09960-20010 
          1. 09961-02060
        NOTE:
        • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.
        • As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0394 in.) or less.
      6. Using SST, disconnect the steering knuckle assembly LH from the front upper No. 2 suspension arm assembly LH.
        • SST: 09960-20010 
          1. 09961-02010
        NOTE:
        • Apply molybdenum grease to the bolt threads and end of the SST bolt.
        • Do not damage the dust cover.
        • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.
        • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
  3. REMOVE FRONT UPPER NO. 1 ARM BRACKET LH 
    1. GTY979751Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE FRONT UPPER NO. 2 ARM BRACKET LH 
    1. GTY978933Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH 
    1. GTY979752Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH 
    1. GTY980143Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals