Caution / Notice / Hint

COMPONENTS (REMOVAL)

Fig 1: Rear Door Belt Moulding Removal Components [12/2022 - 12/2023] (1 Of 2)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1	DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL	-	-	-	-
2	REAR DOOR INSIDE HANDLE BEZEL PLUG LH	69284D	See step 2	-	-
3	REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL	-	See step 3	-	-
4	REAR DOOR TRIM BOARD SUB-ASSEMBLY LH	67604	See step 4	-	-
5	REAR DOOR GLASS INNER WEATHERSTRIP LH	68174A	-	-	-
6	REAR DOOR BELT REAR SEAL LH	68199	See step 6	-	-

Fig 2: Rear Door Belt Moulding Removal Components [12/2022 - 12/2023] (2 Of 2)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Procedure		Part Name Code	Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7	REAR DOOR ARMREST SET BRACKET LH	67646A	-	-	-
8	REAR DOOR SERVICE HOLE COVER LH	67842E	See step 8	-	-
9	REAR DOOR GLASS RUN LH	68152C	-	-	-
10	REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH	67408E	-	-	-
11	REAR DOOR QUARTER WINDOW GLASS LH	68124B	-	-	-
12	REAR DOOR GLASS SUB-ASSEMBLY LH	68104	See step 12	-	-
13	REAR DOOR BELT MOULDING ASSEMBLY LH	75740	See step 13	-	-

•

Non-reusable part

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door belt moulding assembly removal/installation are shown below.

NECESSARY PROCEDURES AFTER PARTS REMOVED/INSTALLED/REPLACED

Replaced Part or Performed Procedures	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
Rear door glass (RH, LH) or rear door glass run (RH, LH) Because of assembly adjustment, etc., causing sliding change, improper reversal has occurred	Power window system initialization	Auto up and down function Jam protection function Catch protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Window open warning function	Refer to INITIALIZATION [11/2020 - 12/2023]

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Lane tracing assist system (for Stereo camera type)	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.	for Stereo Camera Type: Refer to INITIALIZATION [11/2021 - ] for Mono Camera Type: Refer to INITIALIZATION [11/2020 - 12/2023]
Lane tracing assist system (for Mono camera type)
Pre-collision system (for Stereo camera type)
Pre-collision system (for Mono camera type)
Lighting system (EXT)
Advanced drive system	Drive the vehicle straight ahead at a vehicle speed of 35 km/h or higher for 30 seconds* or more.	Refer to INITIALIZATION [11/2021 - ]

*: This can be completed by doing this for 30 seconds continuously or for a total of 30 seconds intermittently.

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Air conditioning system	After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized.	-

Use the same procedure for both the RH and LH side.
The procedure described below is for the LH side.