LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Mirai XLE >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter / Gauge System - Diagnostic Codes (1 Of 3) >> Meter / Gauge System >> DTC B1507-18: Turn Signal Light Circuit Current Below Threshold [11/2020 - 11/2021] >> Procedure

DTC B1507-18: Turn Signal Light Circuit Current Below Threshold [11/2020 - 11/2021]: Procedure

  1. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/o Advanced Drive A
      w/ Advanced Drive B

    Result: 

    B 

    See step  31

    Result: 

    A 

    See step  2

  2. INSPECT LIGHTS 
    1. Inspect the illumination of each turn signal light.

      Result

      Result Proceed to
      RH side turn signal light or LH side turn signal light does not illuminate. A
      Side turn signal light LH and rear turn signal light LH does not blink. B
      Front turn signal light LH does not blink. C
      Side turn signal light LH does not blink. D
      Rear turn signal light LH does not blink. E
      Side turn signal light RH and rear turn signal light RH does not blink. F
      Front turn signal light RH does not blink. G
      Side turn signal light RH does not blink. H
      Rear turn signal light RH does not blink. I

    Result: 

    A 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    C 

    See step  6

    Result: 

    D 

    See step  9

    Result: 

    E 

    See step  15

    Result: 

    F 

    See step  17

    Result: 

    G 

    See step  20

    Result: 

    H 

    See step  23

    Result: 

    I 

    See step  29

    Result: 

    B 

    See step  3

  3. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Reverse Shift-linked Mirror A
      w/o Reverse Shift-linked Mirror B

    Result: 

    B 

    See step  5

    Result: 

    A 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - COMBINATION METER ASSEMBLY) 

    Pre-procedure1

    • Disconnect the E25 front multiplex network door ECU LH connector.
    • Disconnect the D42 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E25-20 (TRNI) - D42-11(TRNL) Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR LH - COMBINATION METER ASSEMBLY) 

    Pre-procedure1

    • Disconnect the E29 outer mirror retractor LH connector.
    • Disconnect the D42 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E29-16 (B) - D42-11(TRNL) Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  6. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Advanced Park A
      w/o Advanced Park B

    Result: 

    B 

    See step  8

    Result: 

    A 

    See step  7

  7. INSPECT FRONT TURN SIGNAL LIGHT ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY LH. Refer to  REMOVAL [11/2020 - 11/2021] 

  8. INSPECT FRONT TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  9. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Reverse Shift-linked Mirror A
      w/o Reverse Shift-linked Mirror B

    Result: 

    B 

    See step  13

    Result: 

    A 

    See step  10

  10. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - COMBINATION METER ASSEMBLY OR BODY GROUND) 

    Pre-procedure1

    • Disconnect the E25 front multiplex network door ECU LH connector.
    • Disconnect the D42 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E25-20 (TRNI) - D42-11 (TRNL) Always Below 1 Ω Ω
      E25-1 (GND) - Body ground Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  11

  11. INSPECT OUTER MIRROR RETRACTOR LH 

    Refer to INSPECTION [11/2020 - 12/2023]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH. Refer to  DISASSEMBLY [11/2020 - 11/2021] 

    Result: 

    NG 

    See step  12

  12. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE OUTER MIRROR RETRACTOR LH. Refer to  DISASSEMBLY [11/2020 - 12/2022] 

    Result: 

    NG 

    REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH. Refer to  REMOVAL [11/2020 - ] 

  13. INSPECT OUTER MIRROR RETRACTOR LH 

    Refer to INSPECTION [11/2020 - 12/2023]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE OUTER MIRROR RETRACTOR LH. Refer to  DISASSEMBLY [11/2020 - 12/2022] 

    Result: 

    OK 

    See step  14

  14. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH. Refer to  REMOVAL [11/2020 - ] 

  15. INSPECT REAR COMBINATION LIGHT CORD LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR COMBINATION LIGHT CORD LH. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    OK 

    See step  16

  16. INSPECT REAR TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE REAR TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  17. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Reverse Shift-linked Mirror A
      w/o Reverse Shift-linked Mirror B

    Result: 

    B 

    See step  19

    Result: 

    A 

    See step  18

  18. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - COMBINATION METER ASSEMBLY) 

    Pre-procedure1

    • Disconnect the E7 front multiplex network door ECU RH connector.
    • Disconnect the D42 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E7-20 (TRNI) - D42-5 (TRNR) Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  19. CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR RH - COMBINATION METER ASSEMBLY) 

    Pre-procedure1

    • Disconnect the E11 outer mirror retractor RH connector.
    • Disconnect the D42 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E11-16 (B) - D42-5 (TRNR) Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  20. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Advanced Park A
      w/o Advanced Park B

    Result: 

    B 

    See step  22

    Result: 

    A 

    See step  21

  21. INSPECT FRONT TURN SIGNAL LIGHT ASSEMBLY RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2020 - 11/2021] 

  22. INSPECT FRONT TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  23. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Reverse Shift-linked Mirror A
      w/o Reverse Shift-linked Mirror B

    Result: 

    B 

    See step  27

    Result: 

    A 

    See step  24

  24. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - COMBINATION METER ASSEMBLY OR BODY GROUND) 

    Pre-procedure1

    • Disconnect the E7 front multiplex network door ECU RH connector.
    • Disconnect the D42 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E7-20 (TRNI) - D42-5 (TRNR) Always Below 1 Ω Ω
      E7-1 (GND) - Body ground Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  25

  25. INSPECT OUTER MIRROR RETRACTOR RH 

    Refer to INSPECTION [11/2020 - 12/2023]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH. Refer to  DISASSEMBLY [11/2020 - 11/2021] 

    Result: 

    NG 

    See step  26

  26. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE OUTER MIRROR RETRACTOR RH. Refer to  DISASSEMBLY [11/2020 - 12/2022] 

    Result: 

    NG 

    REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2020 - ] 

  27. INSPECT OUTER MIRROR RETRACTOR RH 

    Refer to INSPECTION [11/2020 - 12/2023]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE OUTER MIRROR RETRACTOR RH. Refer to  DISASSEMBLY [11/2020 - 12/2022] 

    Result: 

    OK 

    See step  28

  28. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2020 - ] 

  29. INSPECT REAR COMBINATION LIGHT CORD RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR COMBINATION LIGHT CORD RH. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    OK 

    See step  30

  30. INSPECT REAR TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE REAR TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  31. INSPECT LIGHTS 
    1. Inspect the illumination of each turn signal light.

      Result

      Result Proceed to
      RH side turn signal light or LH side turn signal light does not illuminate. A
      Side turn signal light LH and rear turn signal light LH does not blink. B
      Front turn signal light LH does not blink. C
      Side turn signal light LH does not blink. D
      Rear turn signal light LH does not blink. E
      Side turn signal light RH and rear turn signal light RH does not blink. F
      Front turn signal light RH does not blink. G
      Side turn signal light RH does not blink. H
      Rear turn signal light RH does not blink. I

    Result: 

    A 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    C 

    See step  33

    Result: 

    D 

    See step  36

    Result: 

    E 

    See step  39

    Result: 

    F 

    See step  41

    Result: 

    G 

    See step  42

    Result: 

    H 

    See step  45

    Result: 

    I 

    See step  48

    Result: 

    B 

    See step  32

  32. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - COMBINATION METER ASSEMBLY) 

    Pre-procedure1

    • Disconnect the E25 front multiplex network door ECU LH connector.
    • Disconnect the D43 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E25-20 (TRNI) - D43-22(TRNL) Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  33. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Advanced Park A
      w/o Advanced Park B

    Result: 

    B 

    See step  35

    Result: 

    A 

    See step  34

  34. INSPECT FRONT TURN SIGNAL LIGHT ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY LH. Refer to  REMOVAL [11/2020 - 11/2021] 

  35. INSPECT FRONT TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  36. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU LH - COMBINATION METER ASSEMBLY OR BODY GROUND) 

    Pre-procedure1

    • Disconnect the E25 front multiplex network door ECU LH connector.
    • Disconnect the D43 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E25-20 (TRNI) - D43-22 (TRNL) Always Below 1 Ω Ω
      E25-1 (GND) - Body ground Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  37

  37. INSPECT OUTER MIRROR RETRACTOR LH 

    Refer to INSPECTION [11/2020 - 12/2023]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU LH. Refer to  DISASSEMBLY [11/2020 - 11/2021] 

    Result: 

    NG 

    See step  38

  38. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE OUTER MIRROR RETRACTOR LH. Refer to  DISASSEMBLY [11/2020 - 12/2022] 

    Result: 

    NG 

    REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH. Refer to  REMOVAL [11/2020 - ] 

  39. INSPECT REAR COMBINATION LIGHT CORD LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR COMBINATION LIGHT CORD LH. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    OK 

    See step  40

  40. INSPECT REAR TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE REAR TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  41. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - COMBINATION METER ASSEMBLY) 

    Pre-procedure1

    • Disconnect the E7 front multiplex network door ECU RH connector.
    • Disconnect the D43 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E7-20 (TRNI) - D43-38 (TRNR) Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  42. CHECK VEHICLE TYPE 
    1. Check vehicle condition.

      Result

      Result  Proceed to 
      w/ Advanced Park A
      w/o Advanced Park B

    Result: 

    B 

    See step  44

    Result: 

    A 

    See step  43

  43. INSPECT FRONT TURN SIGNAL LIGHT ASSEMBLY RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2020 - 11/2021] 

  44. INSPECT FRONT TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE FRONT TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

  45. CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU RH - COMBINATION METER ASSEMBLY OR BODY GROUND) 

    Pre-procedure1

    • Disconnect the E7 front multiplex network door ECU RH connector.
    • Disconnect the D43 combination meter assembly connector.
    • Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition Result
      E7-20 (TRNI) - D43-38 (TRNR) Always Below 1 Ω Ω
      E7-1 (GND) - Body ground Always Below 1 Ω Ω

      Result

      Proceed to
      OK
      NG

    Post-procedure1

    • None

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  46

  46. INSPECT OUTER MIRROR RETRACTOR RH 

    Refer to INSPECTION [11/2020 - 12/2023]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE FRONT MULTIPLEX NETWORK DOOR ECU RH. Refer to  DISASSEMBLY [11/2020 - 11/2021] 

    Result: 

    NG 

    See step  47

  47. INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE OUTER MIRROR RETRACTOR RH. Refer to  DISASSEMBLY [11/2020 - 12/2022] 

    Result: 

    NG 

    REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH. Refer to  REMOVAL [11/2020 - ] 

  48. INSPECT REAR COMBINATION LIGHT CORD RH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE REAR COMBINATION LIGHT CORD RH. Refer to  REMOVAL [11/2020 - 11/2021] 

    Result: 

    OK 

    See step  49

  49. INSPECT REAR TURN SIGNAL LIGHT LED 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    NG 

    REPLACE REAR TURN SIGNAL LIGHT LED. Refer to  DISASSEMBLY [11/2020 - ] 

scientia non olet · About LEMON Manuals