LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Mirai Limited >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Seat Heater System - Diagnostic Codes & Symptom Tests >> Seat Heater System >> Seat Heater for Rear Left Seat does not Operate [12/2023 - ] >> Procedure

Seat Heater for Rear Left Seat does not Operate [12/2023 - ]: Procedure

  1. PERFORM ACTIVE TEST USING GTS (SEAT HEATER) 
    1. Perform the Active Test according to the display on the GTS.
      1. w/ Front LiDAR Sensor:

        Body Electrical > Air Conditioner > Active Test 

        Tester Display Measurement Item Control Range Diagnostic Note
        Rear Left Seat Heater Rear left side seat heater operation OFF/ON -

        Body Electrical > Air Conditioner > Active Test 

        Tester Display
        Rear Left Seat Heater
      2. w/o Front LiDAR Sensor:

        Body Electrical > Air Conditioner > Active Test 

        Tester Display Measurement Item Control Range Diagnostic Note
        Rear Left Seat Heater Rear left side seat heater operation OFF/ON -

        Body Electrical > Air Conditioner > Active Test 

        Tester Display
        Rear Left Seat Heater

      OK

      Rear left side seat heater operates normally.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    See step  4

    Result: 

    OK 

    See step  2

  2. REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY 
    1. Replace the air conditioner amplifier assembly with a new one or known good one.

      Refer to REMOVAL [11/2020 - ]

      Result

      Proceed to
      OK

    Result: 

    OK 

    See step  3

  3. CHECK REAR SEAT HEATER OPERATION 
    1. Check the rear left side seat heater operation.

      Refer to OPERATION CHECK [11/2020 - ]

      OK

      Rear left side seat heater operates normally.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END (AIR CONDITIONING AMPLIFIER ASSEMBLY WAS DEFECTIVE) 

    Result: 

    NG 

    REPLACE COOLER CONTROL SWITCH ASSEMBLY. Refer to  REMOVAL [11/2020 - ] 

  4. CHECK HARNESS AND CONNECTOR (SEAT HEATER CONTROL SUB-ASSEMBLY [REAR SEAT LH] POWER SOURCE CIRCUIT) 
    1. Disconnect the M3 seat heater control sub-assembly (rear seat LH) connector.
    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Switch Condition Specified Condition
      M3-1 (+B1) - Body ground Ignition switch ON 11 to 14 V
      M3-1 (+B1) - Body ground Ignition switch off Below 1 V

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (AIR CONDITIONER AMPLIFIER ASSEMBLY - SEAT HEATER CONTROL SUB-ASSEMBLY [REAR SEAT LH]) 
    1. Disconnect the D79 air conditioning amplifier assembly connector.
    2. Disconnect the M3 seat heater control sub-assembly (rear seat LH) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D79-24 (SM2L) - M3-5 (SWR) Always Below 1 Ω
      D79-24 (SM2L) or M3-5 (SWR) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. CHECK HARNESS AND CONNECTOR (SEATBACK HEATER ASSEMBLY LH - SEAT HEATER CONTROL SUB-ASSEMBLY [REAR SEAT LH]) 
    1. Disconnect the M1 seatback heater assembly LH connector.
    2. Disconnect the M3 seat heater control sub-assembly (rear seat LH) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M1-4 - M3-10(E) Always Below 1 Ω
      M1-1 - M3-7(HTR1) Always Below 1 Ω
      M1-4 or M3-10 (E) - Body ground Always 10 kΩ or higher
      M1-1 or M3-7(HTR1) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  7

  7. CHECK HARNESS AND CONNECTOR (SEATBACK HEATER ASSEMBLY LH - BODY GROUND) 
    1. Disconnect the M1 seatback heater assembly LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      M1-5 - Body ground Always Below 1 Ω
      M1-5 - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  8

  8. INSPECT SEATBACK HEATER ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE SEATBACK HEATER ASSEMBLY LH. Refer to  REMOVAL [11/2020 - ] 

    Result: 

    OK 

    See step  9

  9. INSPECT SEAT CUSHION HEATER ASSEMBLY LH 

    Refer to INSPECTION [11/2020 - ]

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    REPLACE SEAT CUSHION HEATER ASSEMBLY LH. Refer to  REMOVAL [11/2020 - ] 

    Result: 

    OK 

    See step  10

  10. REPLACE SEAT HEATER CONTROL SUB-ASSEMBLY (REAR SEAT LH) 
    1. Replace the seat heater control sub-assembly (rear seat LH) with a new one or known good one.

      Refer to REMOVAL [11/2020 - ]

      Result

      Proceed to
      OK

    Result: 

    OK 

    See step  11

  11. CHECK REAR SEAT HEATER OPERATION 
    1. Check the rear left side seat heater operation.

      Refer to OPERATION CHECK [11/2020 - ]

      OK

      Rear left side seat heater operates normally.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    END (SEAT HEATER CONTROL SUB-ASSEMBLY (REAR SEAT LH) WAS DEFECTIVE) 

    Result: 

    NG 

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY. Refer to  REMOVAL [11/2020 - ]