Speedometer Malfunction [08/2015 - ]: Procedure

1. Check for DTCs (Refer to DTC CHECK / CLEAR [08/2015 - ] ).
   RESULT
   
   

   Result	Proceed to
   CAN communication DTC is not output	A
   CAN communication DTC is output	B

Result: 

B 

Go to CAN COMMUNICATION SYSTEM 

(Refer to HOW TO PROCEED WITH TROUBLESHOOTING [08/2015 - ] )

Result: 

A 

See step  2

1. Check for DTCs (Refer to DTC CHECK / CLEAR [08/2015 - ] ).

Result: 

NG 

Go to DIAGNOSTIC TROUBLE CODE CHART 

(Refer to DIAGNOSTIC TROUBLE CODE CHART [08/2015 - 08/2016] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2016 - 08/2017] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2017 - 08/2018] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2018 - 08/2019] , or refer to DIAGNOSTIC TROUBLE CODE CHART [08/2019 - ] )

Result: 

OK 

See step  3

1. Operate the Techstream according to the display and select Active Test (Refer to DATA LIST / ACTIVE TEST [08/2015 - ] ).
   COMBINATION METER
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Speed Meter Operation	Speedometer	0, 40, 80, 120, 160, 200, 240 or 280	Acceptable range (mph or km/h): [Control range → Speedometer display] for mph  40 → 39.5 to 42.5 80 → 80.5 to 84.5 120 → 120.5 to 126 for km/h  40 → 38 to 42 80 → 78 to 84 120 → 119 to 125 160 → 159 to 167 200 → 199 to 209 240 → 239 to 251 Perform the test with the vehicle stopped and engine idling.

   HINT: 

   • Make sure that the vehicle is stopped and the engine is idling. The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.
   • The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.
   • The needle position should be within the acceptable tolerance.

     OK

     Needle indication is normal.

Result: 

NG 

REPLACE COMBINATION METER ASSEMBLY 

(Refer to REMOVAL [08/2015 - ] )

Result: 

OK 

See step  4

1. Operate the Techstream according to the display and select Data List (Refer to DATA LIST / ACTIVE TEST [08/2015 - ] ).
   COMBINATION METER
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Vehicle Speed meter	Vehicle speed/Min.: 0 (0), Max.: 255 (158)	Almost same as actual speed (when driving)	Unit: km/h (mph)

   OK

   Vehicle speed displayed on the Techstream is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).

Result: 

OK 

REPLACE COMBINATION METER ASSEMBLY 

(Refer to REMOVAL [08/2015 - ] )

Result: 

NG 

See step  5

1. Operate the Techstream according to the display and select Data List (Refer to DATA LIST / ACTIVE TEST [08/2015 - ] ).
   ABS/VSC/TRAC
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   FR Wheel Speed	Wheel speed sensor FR reading/Min.: 0 (0), Max.: 326 (202)	Actual wheel speed	A similar speed is indicated on the speedometer.
   FL Wheel Speed	Wheel speed sensor FL reading/Min.: 0 (0), Max.: 326 (202)	Actual wheel speed	A similar speed is indicated on the speedometer.
   RR Wheel Speed	Wheel speed sensor RR reading/Min.: 0 (0), Max.: 326 (202)	Actual wheel speed	A similar speed is indicated on the speedometer.
   RL Wheel Speed	Wheel speed sensor RL reading/Min.: 0 (0), Max.: 326 (202)	Actual wheel speed	A similar speed is indicated on the speedometer.

   OK

   Vehicle speed displayed on the Techstream is almost the same as actual vehicle speed measured using speedometer tester (calibrated chassis dynamometer).

Result: 

OK 

REPLACE COMBINATION METER ASSEMBLY 

(Refer to REMOVAL [08/2015 - ] )

Result: 

NG 

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY 

(Refer to REMOVAL [08/2015 - ] )