LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Highlander Platinum, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 51 (Emission Control System (T24A-FTS) - Service Information) >> Canister >> Removal [10/2022 - ] >> Procedure

Removal [10/2022 - ]: Procedure

WARNING: This page is about a different car, the 2025 Toyota Highlander, 2024 Toyota Highlander, and 2023 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 10 [10/2022 - 11/2023] , or refer to PROCEDURE - Step 10 [11/2023 - ]

  2. REMOVE FRONT FLOOR COVER LH 

    Refer to PROCEDURE - Step 3 [10/2022 - 11/2023] , or refer to PROCEDURE - Step 3 [11/2023 - ]

  3. DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY 
    NOTE:
    • Remove any dirt or foreign matter on the tube connector before performing this work.
    • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (leak detection pump sub-assembly).
    • Perform this work by hand. Do not use any tools.
    • Do not forcibly bend, twist or fuel tank evaporation vent tube sub-assembly.
    • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank evaporation vent tube sub-assembly.
    • If the tube connector and pipe (leak detection pump sub-assembly) are stuck, push and pull to release them.
    1. GTY1103757Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Fuel Tank Evaporation Vent Tube Sub-assembly *2 Pipe (Canister (Charcoal Canister Assembly))
      *a Retainer *b Tab
      *c Tube Connector *d O-ring
      Pinch Pull
      Pull off - -
      1. Pinch the tabs of the retainer to disengage the lock claws and pull it down.

        HINT: 

        Do not remove the retainer.

      2. Pull off the fuel tank evaporation vent tube sub-assembly.
  4. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY (NO. 2 CHARCOAL CANISTER ASSEMBLY) 
    NOTE:
    • Remove any dirt or foreign matter on the tube connector before performing this work.
    • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).
    • Perform this work by hand. Do not use any tools.
    • Do not forcibly bend, twist or turn the fuel tank vent hose sub-assembly.
    • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose sub-assembly.
    • If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.
    1. GTY1103758Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Fuel Tank Vent Hose Sub-assembly (No. 2 Charcoal Canister Assembly) *2 Pipe (Canister (Charcoal Canister Assembly))
      *a Retainer *b Tab
      *c Tube Connector *d O-ring
      Pinch Pull
      Pull off - -
      1. Pinch the tabs of the retainer to disengage the lock claws and pull it down.

        HINT: 

        Do not remove the retainer.

      2. Pull off the fuel tank vent hose sub-assembly.
  5. DISCONNECT FUEL EMISSION HOSE 
    1. GTY1106579Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY) 
    1. GTY1106576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. GTY1106575Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE CHARCOAL CANISTER OUTLET GUIDE 
    1. GTY1078220Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. DISCONNECT NO. 7 FUEL TANK BREATHER TUBE 
    NOTE:
    • Remove any dirt or foreign matter on the tube connector before performing this work.
    • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).
    • Perform this work by hand. Do not use any tools.
    • Do not forcibly bend, twist or turn the No. 7 fuel tank breather tube.
    • Protect the disconnected parts by covering them with plastic bags after disconnecting the No. 7 fuel tank breather tube.
    • If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.
    1. GTY1103334Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 7 Fuel Tank Breather Tube *2 Pipe (Leak Detection Pump Sub-assembly)
      *a Retainer *b O-ring
      *c Tube Connector - -
      Push Pull
      1. Push the fuel tank breather tube firmly toward the leak detection pump sub-assembly.
      2. Pinch the tube connector as shown in the illustration.
      3. Pull off the No. 7 fuel tank breather tube from the pipe (leak detection pump sub-assembly).
    2. GTY1109056Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE NO. 2 CHARCOAL CANISTER ASSEMBLY 
    1. GTY1109055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY 

    HINT: 

    Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.

    1. GTY1106661Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Before removing the leak detection pump sub-assembly, clean the No. 2 charcoal canister sub-assembly by blowing air into it to ensure that the No. 2 charcoal canister sub-assembly is free of foreign matter.
        NOTE:
        • Make sure to clean the No. 2 charcoal canister sub-assembly using air only.
        • Do not use gasoline, thinners or solvents.
      2. While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.
    2. GTY1109393Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Check if the No. 2 charcoal canister sub-assembly contains foreign matter such as mud or water.
        1. Visually check that the inside of the No. 2 charcoal canister sub-assembly is free of foreign matter.
        2. Hold the No. 2 charcoal canister sub-assembly upside down to make sure that it is free of foreign matter.
scientia non olet · About LEMON Manuals