LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Highlander Platinum, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Meter / Gauge System (12.3 Inch Display) - Diagnostic Codes & Circuit Tests) >> METER / GAUGE SYSTEM (for 12.3 Inch Display) >> DTC B1321-87: Lost Communication with EMV Missing Message [11/2023 - ] >> Procedure

DTC B1321-87: Lost Communication with EMV Missing Message [11/2023 - ]: Procedure

WARNING: This page is about a different car, the 2025 Toyota Highlander, 2024 Toyota Highlander, and 2023 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. CONFIRM MODEL 
    1. Choose the model to be inspected.

      Result

      Result Proceed to
      w/ Headup Display System A
      w/o Headup Display System B

    Result: 

    B 

    See step  5

    Result: 

    A 

    See step  2

  2. CHECK FOR DTC (EACH SYSTEM) 
    1. Check each system for DTCs.

      Body Electrical > Combination Meter > Trouble Codes 

      Body Electrical > Navigation System > Trouble Codes 

      Body Electrical > Head Up Display > Trouble Codes 

    2. Confirm the DTC combinations of the following table.
      DTC Output Pattern DTC Output Part Name
      (Display on GTS)
      Combination Meter Assembly
      (Combination Meter)      		 Radio and Display Receiver Assembly
      (Navigation System)      		 Meter Mirror Sub-assembly
      (Headup Display)
      1 B1321-87 U11D0-87
      U11D1-87
      U11D3-87
      (Simultaneously output)      		 B1321-87
      2 B1321-87 U11D0-87 Not output
      3 B1321-87 Not output B1321-87
      4 B1321-87 Not output Not output

      Result

      Result Proceed to
      DTC output pattern 1 A
      DTC output pattern 2 B
      DTC output pattern 3 C
      DTC output pattern 4 D

    Result: 

    B 

    See step  4

    Result: 

    C 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    D 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2019 - ] 

    Result: 

    A 

    See step  3

  3. INSPECT EACH ECU (INTERNAL MALFUNCTION) 
    1. Remove 1 of the following ECUs.
    2. Measure the resistance of the removed ECU.
      NOTE:
      • Refer to the following table for the specified conditions of each ECU.
      • If the specified conditions are met, repeat the inspection procedure from step (a) for another ECU.

      HINT: 

      If the results of an ECU are not as specified, it is suspected that the ECU is the cause of the DTC.

      1. Inspect the radio and display receiver assembly.

        Standard Resistance

        Tester Connection Condition Specified Condition
        H108-11 (CNH1) - H108-12 (CNL1) Always 108 to 132 Ω
        GTY1110368Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Radio and Display Receiver Assembly)
      2. Inspect the meter mirror sub-assembly.
        GTY1119064Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Meter Mirror Sub-assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        H31-14 (TX+) - H31-15 (TX-) Always 200 Ω or higher
      3. Inspect the mobile wireless charger cradle assembly.
        GTY1121919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Mobile Wireless Charger Cradle Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        H116-5 (CANH) - H116-6 (CANL) Always 200 Ω or higher
      4. Inspect the combination meter assembly.
        GTY1180293Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Meter Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        H113-32 (MSCH) - H113-15 (MSCL) Always 108 to 132 Ω

        Result

        Result  Proceed to
        The results of all ECUs are as specified A
        The results of the radio and display receiver assembly are not as specified B
        The results of the meter mirror sub-assembly are not as specified C
        The results of the Mobile wireless charger cradle assembly are not as specified D
        The results of the combination meter assembly are not as specified E

    Result: 

    A 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    B 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    C 

    REPLACE METER MIRROR SUB-ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    D 

    REPLACE MOBILE WIRELESS CHARGER CRADLE ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    E 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2019 - ] 

  4. CHECK HARNESS AND CONNECTOR (LOCAL BUS COMMUNICATION CIRCUIT) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.
    2. Disconnect the H113 combination meter assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      H113-32 (MSCH) - H113-15 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2019 - ] 

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  5. CHECK FOR DTC (EACH SYSTEM) 
    1. Check each system for DTCs.

      Body Electrical > Combination Meter > Trouble Codes 

      Body Electrical > Navigation System > Trouble Codes 

    2. Confirm the DTC combinations of the following table.
      DTC Output Pattern DTC Output Part Name
      (Display on GTS)
      Combination Meter Assembly
      (Combination Meter)      		 Radio and Display Receiver Assembly
      (Navigation System)
      1 B1321-87 U11D0-87
      U11D3-87
      (Simultaneously output)
      2 B1321-87 Not output

      Result

      Result  Proceed to
      DTC output pattern 1 A
      DTC output pattern 2 B

    Result: 

    B 

    See step  7

    Result: 

    A 

    See step  6

  6. INSPECT EACH ECU (INTERNAL MALFUNCTION) 
    1. Remove 1 of the following ECUs.
    2. Measure the resistance of the removed ECU.
      NOTE:
      • Refer to the following table for the specified conditions of each ECU.
      • If the specified conditions are met, repeat the inspection procedure from step (a) for another ECU.

      HINT: 

      If the results of an ECU are not as specified, it is suspected that the ECU is the cause of the DTC.

      1. Inspect the radio and display receiver assembly.

        Standard Resistance

        Tester Connection Condition Specified Condition
        H108-11 (CNH1) - H108-12 (CNL1) Always 108 to 132 Ω
        GTY1110368Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Radio and Display Receiver Assembly)
      2. Inspect the meter mirror sub-assembly.

        Standard Resistance

        Tester Connection Condition Specified Condition
        H116-5 (CANH) - H116-6 (CANL) Always 200 Ω or higher
        GTY1121919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Mobile Wireless Charger Cradle Assembly)
      3. Inspect the combination meter assembly.
        GTY1180293Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Component without harness connected
        (Combination Meter Assembly)

        Standard Resistance

        Tester Connection Condition Specified Condition
        H113-32 (MSCH) - H113-15 (MSCL) Always 108 to 132 Ω

        Result

        Result  Proceed to
        The results of all ECUs are as specified A
        The results of the radio and display receiver assembly are not as specified B
        The results of the Mobile wireless charger cradle assembly are not as specified C
        The results of the combination meter assembly are not as specified D

    Result: 

    A 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    B 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    C 

    REPLACE MOBILE WIRELESS CHARGER CRADLE ASSEMBLY. Refer to  REMOVAL [10/2022 - ] 

    Result: 

    D 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2019 - ] 

  7. CHECK FOR DTC (METER / GAUGE SYSTEM) 
    1. Disconnect the cable from the negative (-) auxiliary battery terminal.

      HINT: 

      By disconnecting the cable from the negative (-) auxiliary battery terminal, the internally stored information related to local bus communication for the combination meter assembly is reset.

    2. Disconnect the H108 Radio and display receiver assembly connector.
    3. Connect the cable to the negative (-) auxiliary battery terminal.
    4. Turn the ignition switch to ON.
    5. Clear the DTCs.

      Body Electrical > Combination Meter > Clear DTCs 

    6. Wait 30 seconds or more.
    7. Check for DTCs.

      Body Electrical > Combination Meter > Trouble Codes 

      HINT: 

      By resetting the internally stored information related to local bus communication, the detection conditions of DTC B1321-87 are not met as the combination meter assembly does not detect the radio receiver assembly. If the combination meter assembly is operating normally, DTC B1321-87 will not be stored.

      Result:

      Result  Proceed to
      DTC B1321-87 is not output A
      DTC B1321-87 is output B

    Result: 

    A 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [11/2023 - ] 

    Result: 

    B 

    REPLACE COMBINATION METER ASSEMBLY. Refer to  REMOVAL [12/2019 - ] 

scientia non olet · About LEMON Manuals