LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Suspension >> Rear Suspension >> Suspension System (Rear) - Service Information (Except Hybrid) >> Rear Trailing Arm >> Removal [03/2020 - 10/2020] >> Procedure

Removal [03/2020 - 10/2020]: Procedure

  1. REMOVE REAR WHEEL 

    Refer to PROCEDURE - Step 1

  2. REMOVE NO. 2 FLOOR UNDER COVER (for 2WD) 
    1. For LH Side:

      See step  2

  3. REMOVE NO. 1 FLOOR UNDER COVER (for 2WD) 
    1. For RH Side:

      See step  3

  4. REMOVE NO. 2 FLOOR UNDER COVER (for AWD) 
    1. For LH Side:
      1. Remove the bolt and 2 clips (A).
        GTY975545Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Disengage the 2 grommets (B) and 2 clips (C) to remove the No. 2 floor under cover.
  5. REMOVE NO. 1 FLOOR UNDER COVER (for AWD) 
    1. For RH Side:
      1. Remove the bolt and 2 clips (A).
        GTY974982Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Disengage the 2 grommets (B) and clip (C) to remove the No. 1 floor under cover.
  6. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (w/o Electric Parking Brake System) 
    1. Remove the nut and separate the No. 3 parking brake cable assembly from the rear trailing arm assembly.
      GTY763032Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. SEPARATE SKID CONTROL SENSOR WIRE (w/o Electric Parking Brake System) 
    1. Disengage the 2 clamps.
      GTY763033Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and separate the skid control sensor wire from the rear trailing arm assembly.
  8. SEPARATE NO. 2 PARKING BRAKE WIRE ASSEMBLY (w/ Electric Parking Brake System) 
    1. Disengage the 2 clamps.
      GTY744164Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the nut and separate the No. 2 parking brake wire assembly from the rear trailing arm assembly.
  9. REMOVE REAR STABILIZER LINK ASSEMBLY (for 2WD) 

    See step  5

  10. REMOVE REAR TRAILING ARM ASSEMBLY 
    1. Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.
      NOTE:
      • When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
      • Make sure to perform this operation with the vehicle kept as low as possible.
      GTY772167Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wooden Block
      *b Transmission Jack
    2. For 2WD:
      1. Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.
        GTY773489Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. For AWD:
      1. Remove the 3 bolts, nut and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.
        GTY957814Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 4 bolts and rear trailing arm assembly.
      GTY763036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE REAR SUSPENSION ARM COVER 
    1. Secure the rear trailing arm assembly in a vise using aluminum plates.
      NOTE:

      Do not overtighten the vise.

      GTY763037Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 4 claws and remove the rear suspension arm cover.
      GTY763021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE REAR SUSPENSION ARM BRACKET 
    1. Remove the bolt, nut and rear suspension arm bracket from the rear trailing arm assembly.
      GTY763026Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals