LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Steering >> Steering Column >> Steering Column - Service Information (Except Hybrid) >> Steering Column Assembly >> Removal [03/2017 - 06/2017] >> Procedure

Removal [03/2017 - 06/2017]: Procedure

  1. PRECAUTION 

    Refer to PRECAUTION [03/2017 - 08/2022]

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD 
  3. REMOVE HORN BUTTON ASSEMBLY 

    Refer to REMOVAL [03/2017 - 06/2017]

  4. REMOVE STEERING WHEEL ASSEMBLY 

    See step  3

  5. REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY 
    NOTE:

    Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.

    1. Release the tilt and telescopic lever and fully extend and lower the steering column assembly.
    2. Lock the tilt and telescopic lever.
    3. Remove the 3 screws.
      GTY767118Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. GTY751112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Push Area
      Push in this direction

      While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover sub-assembly.

  6. REMOVE UPPER STEERING COLUMN COVER 
    1. Disengage the claw and separate the upper steering column cover.
      GTY771789Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Separate in this direction
    2. GTY767110Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Disengage the 2 claws and 4 clips to remove the upper steering column cover.

  7. REMOVE TRANSPONDER KEY COIL (w/o Smart Key System) 
    1. Disconnect the connector.
      GTY767112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 claws and remove the transponder key coil.
  8. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
    NOTE:
    • Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
    1. Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.
    2. Using pliers, expand the clamp.
      GTY768068Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Clamp
    3. While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.
  9. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY 

    Refer to REMOVAL [03/2017 - 06/2017]

  10. REMOVE NO. 1 AIR DUCT 
    1. Remove the 2 bolts.
      GTY764586Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a View A
      Front
    2. Disengage the 3 claws to remove the No. 1 air duct.
      NOTE:

      Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.

  11. REMOVE FRONT WHEEL LH 

    Refer to REMOVAL [03/2017 - 06/2017]

  12. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY 

    Refer to PROCEDURE - Step 9

  13. REMOVE STEERING COLUMN HOLE COVER 
    1. Turn back the floor carpet.
    2. Remove the clip.
      GTY767108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 2 clips to remove the steering column hole cover.
  14. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY 
    1. Using a screwdriver, loosen the clamp as shown in the illustration.
      GTY767107Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt and slide the steering intermediate shaft assembly.
      NOTE:

      Do not remove the steering intermediate shaft assembly from the steering column assembly.

      GTY748764Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Matchmark
    3. Put matchmarks on the steering intermediate shaft assembly and the steering column assembly.
    4. Remove the steering intermediate shaft assembly from the steering column assembly.
  15. REMOVE STEERING COLUMN ASSEMBLY 
    1. Disconnect each connector and disengage each wire harness clamp from the steering column assembly.
    2. Remove the bolt, 2 nuts and steering column assembly.
      GTY767111Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals