LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 23 (Engine Cooling System (A25A-FKS) - Service Information (Except Hybrid)) >> FLOW SHUTTING VALVE (for ATF) >> Removal [10/2020 - ] >> Procedure

Removal [10/2020 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. REMOVE BATTERY 

    Refer to REMOVAL [10/2020 - ]

  2. REMOVE ECM 

    Refer to REMOVAL [10/2020 - 08/2022] , or refer to REMOVAL [08/2022 - ]

  3. REMOVE BATTERY CLAMP SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 25 [10/2020 - 08/2022] , or refer to PROCEDURE - Step 25 [08/2022 - ]

  4. REMOVE FRONT WHEEL LH 
  5. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH 

    Refer to PROCEDURE - Step 8 [10/2020 - 08/2022] , or refer to PROCEDURE - Step 8 [08/2022 - ]

  6. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH 

    Refer to PROCEDURE - Step 9 [10/2020 - 08/2022] , or refer to PROCEDURE - Step 9 [08/2022 - ]

  7. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 10 [10/2020 - 08/2022] , or refer to PROCEDURE - Step 10 [08/2022 - ]

  8. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 11 [10/2020 - 08/2022] , or refer to PROCEDURE - Step 11 [08/2022 - ]

  9. REMOVE FRONT FENDER APRON SEAL LH 

    Refer to PROCEDURE - Step 12 [10/2020 - 08/2022] , or refer to PROCEDURE - Step 12 [08/2022 - ]

  10. DRAIN ENGINE COOLANT 

    Refer to PROCEDURE - Step 1

  11. REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE) 
    1. Disengage the 3 clamps to remove the transmission breather clamp.
      GTY771515Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 3 clamps to remove the hose clamp.
      GTY754106Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disengage the 2 clamps to disconnect the flow shutting valve (No. 1 water by-pass hose) and transmission breather hose from the hose clamp.
      GTY754107Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the water outlet.
      GTY772835Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and water outlet.

    5. Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the transmission oil cooler.
      GTY760085Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and transmission oil cooler.

    6. Disconnect the flow shutting valve connector.
      GTY760088Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the bolt and flow shutting valve (No. 1 water by-pass hose).
      GTY754108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals