LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Drivelines & Axles >> Wheel Hubs >> Rear Axle Hub Bolt (W/O Electric Parking Brake System) - Service Information (Except Hybrid) >> REAR AXLE HUB BOLT (w/o Electric Parking Brake System) >> Replacement [03/2017 - ] >> Procedure

Replacement [03/2017 - ]: Procedure

  1. REMOVE REAR WHEEL 

    Refer to PROCEDURE - Step 1 [03/2017 - 06/2017] , or refer to PROCEDURE - Step 1 [06/2017 - ]

  2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY 
    1. Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.
    2. Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly.
      NOTE:

      Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.

  3. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG 

    Refer to PROCEDURE - Step 12

  4. REMOVE REAR DISC 

    Refer to PROCEDURE - Step 13

  5. REMOVE REAR AXLE HUB BOLT 
    1. Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

      Recommended Service Nut

      Thread diameter: 12.0 mm (0.472 in.)

      Thread pitch: 1.5 mm (0.0591 in.)

      NOTE:

      Install the service nuts to prevent damage to the rear axle hub bolts.

      GTY760612Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Service Nut
    2. Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.
      • SST: 09611-12010 
      NOTE:

      Do not damage the threads of the rear axle hub bolts.

  6. INSTALL REAR AXLE HUB BOLT 
    1. Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
      GTY768208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Service Nut
      *b Washer
    2. Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

      Recommended Service Nut

      Thread diameter: 12.0 mm (0.472 in.)

      Thread pitch: 1.5 mm (0.0591 in.)

      HINT: 

      Recommended washer thickness is 5 mm (0.197 in.) or more.

    3. Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
      NOTE:
      • Install the service nuts to prevent damage to the rear axle hub bolts.
      • Do not damage the threads of the rear axle hub bolts.
    4. Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
  7. INSTALL REAR DISC 

    Refer to PROCEDURE - Step 1

  8. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG 

    Refer to PROCEDURE - Step 2

  9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY 
    1. Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

      Torque: 107 N*m (1091 kgf*cm, 79 ft.*lbf) 

    2. Install the rear flexible hose to the rear flexible hose bracket with the bolt.

      Torque: 29 N*m (296 kgf*cm, 21 ft.*lbf) 

  10. ADJUST PARKING BRAKE 

    Refer to ADJUSTMENT [03/2017 - ]

  11. INSTALL REAR WHEEL 

    Refer to PROCEDURE - Step 1 [03/2017 - 06/2017] , or refer to PROCEDURE - Step 1 [06/2017 - ]

scientia non olet · About LEMON Manuals