LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Brakes >> Parking Brake System >> Parking Brake System (W/O Electric Parking Brake System) - Inspection And Adjustment (Except Hybrid) >> PARKING BRAKE SYSTEM (w/o Electric Parking Brake System) >> Adjustment [03/2017 - ] >> Procedure

Adjustment [03/2017 - ]: Procedure

  1. INSPECT PARKING BRAKE PEDAL TRAVEL 
    1. Completely release the parking brake pedal assembly.
    2. Fully depress the parking brake pedal assembly to engage the parking brake.
    3. Depress the parking brake pedal assembly again to disengage the parking brake.
    4. Slowly depress the parking brake pedal assembly using the specified force, and count the number of clicks.
      GTY315513Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Parking Brake Pedal Travel

      7 to 12 notches at 300 N (31 kgf, 67.4 lbf)

      If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.

  2. ADJUST PARKING BRAKE PEDAL TRAVEL 
    1. Completely release the parking brake pedal assembly.
    2. Turn the No. 1 wire adjusting nut until the parking brake pedal travel is corrected to within the specified range.

      Parking Brake Pedal Travel

      7 to 12 notches at 300 N (31 kgf, 67.4 lbf)

      NOTE:

      If the No. 1 wire adjusting nut has been removed from the No. 1 parking brake cable assembly, replace the No. 1 wire adjusting nut with a new one.

      GTY762452Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the rear wheels.

      Refer to PROCEDURE - Step 1 [03/2017 - 06/2017] , or refer to PROCEDURE - Step 1 [06/2017 - ]

    4. Temporarily install the hub nuts to the hub bolts.

      HINT: 

      Make sure to tighten the hub nuts so that the rear disc is secure.

    5. Remove the parking brake shoe adjusting hole plug.
    6. Turn the parking brake shoe adjuster and expand the shoes until the disc locks.
      GTY755906Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Contract
      Expand
    7. Turn and contract the parking brake shoe adjuster until the rear disc can rotate smoothly.

      Standard

      Returns 8 notches.

    8. Check that there is no brake drag against the shoe.
    9. Operate the parking brake pedal assembly 3 to 4 times.
    10. Turn the No. 1 wire adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking Brake Pedal Travel

      7 to 12 notches at 300 N (31 kgf, 67.4 lbf)

    11. Operate the parking brake pedal assembly 3 to 4 times.
    12. Check the parking brake pedal travel.

      Parking Brake Pedal Travel

      7 to 12 notches at 300 N (31 kgf, 67.4 lbf)

    13. Install the parking brake shoe adjusting hole plug.
    14. Check that the parking brake does not drag.
    15. Remove the hub nuts from the hub bolts.
    16. Install the rear wheels.

      Refer to PROCEDURE - Step 1 [03/2017 - 06/2017] , or refer to PROCEDURE - Step 1 [06/2017 - ]

  3. INSPECT BRAKE WARNING LIGHT 
    1. When operating the parking brake pedal assembly, check that the brake warning light illuminates.

      Standard

      The brake warning light always illuminates at the first click.

scientia non olet · About LEMON Manuals