LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information (2 Of 2) (Except Hybrid) >> Roof Headlining >> Removal [03/2017 - 06/2017] >> Procedure

Removal [03/2017 - 06/2017]: Procedure

  1. REMOVE FRONT SEAT ASSEMBLY LH 

    Refer to REMOVAL [03/2017 - 09/2019]

  2. REMOVE FRONT SEAT ASSEMBLY RH 

    Refer to REMOVAL [03/2017 - 09/2019]

  3. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [03/2017 - 06/2017]

  4. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. Disengage the claw as shown in the illustration.
      GTY770863Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction

      HINT: 

      Use the same procedure for the front side and rear side.

    2. Disengage the 8 claws and guide to remove the front door scuff plate LH as shown in the illustration.
      GTY757498Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH 
    1. Remove the clip.
      GTY755525Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    2. Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.
  6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 3

  7. REMOVE FRONT PILLAR GARNISH LH 
    1. Apply protective tape around the front pillar garnish LH as shown in the illustration.
      GTY753026Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      HINT: 

      Let the front pillar garnish LH hang from the front pillar garnish clip.

      GTY759274Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Pillar Garnish Clip
      Place Hand Here
      Remove in this Direction
    3. While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.
      GTY774307Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Front Pillar Garnish Clip
      Remove in this Direction
      NOTE:
      • The front pillar garnish clip is reusable if it is not damaged.
      • If the front pillar garnish clip is damaged, replace it with a new one.

      HINT: 

      When the front pillar garnish clip cannot be disengaged easily:

      1. While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.
        GTY765420Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Move in this Direction
      2. While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.
        GTY742909Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Pull in this Direction
    4. Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
      GTY741331Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Remove the clip from the front pillar garnish LH.
    6. Protect the curtain shield airbag assembly LH.
      GTY745698Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      *b Adhesive Tape
      1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
        NOTE:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  8. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Disengage the claw as shown in the illustration.
      GTY744700Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Disengage the 5 claws and guide to remove the rear door scuff plate LH as shown in the illustration.
      GTY749440Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
  9. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 2

  10. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) 

    Refer to PROCEDURE - Step 7

  11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 8

  12. REMOVE LOWER CENTER PILLAR GARNISH LH 
    1. Disengage the 2 claws as shown in the illustration.
      GTY747849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.
      GTY752951Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
  13. REMOVE UPPER CENTER PILLAR GARNISH LH 
    1. Using a clip remover, remove the 2 clips.
      GTY770193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the guide as shown in the illustration.
      GTY759191Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    3. Disengage the clip and 2 guides to remove the upper center pillar garnish LH as shown in the illustration.
      GTY757535Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    4. Remove the clip from the upper center pillar garnish LH.
  14. REMOVE INNER ROOF SIDE GARNISH LH 
    1. Disengage the 3 clips as shown in the illustration.
      GTY763473Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here
      Remove in this Direction
    2. Disengage the 2 guides to remove the inner roof side garnish LH as shown in the illustration.
      GTY761666Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    3. Remove the 3 clips from the inner roof side garnish LH.
  15. REMOVE FRONT DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  18. REMOVE FRONT PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  19. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  20. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  21. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) 

    HINT: 

    Use the same procedure as for the LH side.

  22. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  23. REMOVE LOWER CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  24. REMOVE UPPER CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  25. REMOVE INNER ROOF SIDE GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  26. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY 

    Refer to REMOVAL [03/2017 - 06/2017]

  27. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY 

    Refer to REMOVAL [03/2017 - ]

  28. REMOVE ROOF CONSOLE BOX ASSEMBLY 

    Refer to PROCEDURE - Step 1

  29. REMOVE ROOM LIGHT ASSEMBLY (for Bulb Type) 

    Refer to PROCEDURE - Step 1

  30. REMOVE SPOT LIGHT ASSEMBLY (for LED Type) 

    Refer to PROCEDURE - Step 3

  31. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover) 

    Refer to PROCEDURE - Step 1

  32. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System) 

    Refer to PROCEDURE - Step 1

  33. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System) 

    Refer to PROCEDURE - Step 2

  34. REMOVE ASSIST GRIP ASSEMBLY 

    HINT: 

    Use the same procedure for all assist grip assemblies.

    1. Insert SST into the cutout of the assist grip cover LH as shown in the illustration.
      GTY747165Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Cutout
      • SST: 09813-00010 
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

    2. Pull SST as shown in the illustration to disengage the claw.
      NOTE:

      To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

      HINT: 

      Use the same procedure for the claw on the other side of the assist grip cover LH.

      GTY752235Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 30 to 45°
      Remove in this Direction
    3. Remove the assist grip cover LH.

      HINT: 

      Use the same procedure for the LH side and RH side.

    4. Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.
      GTY745991Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
    5. Remove the 2 clips from the vehicle body.
  35. REMOVE REAR ASSIST GRIP ASSEMBLY LH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  36. REMOVE REAR ASSIST GRIP ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the assist grip assembly.

  37. REMOVE VISOR BRACKET COVER LH 
    1. Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover LH.
      GTY744804Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Insert Moulding Remover Here
  38. REMOVE VISOR ASSEMBLY LH 
    1. for "TORX" Screw:
      1. Using a T25 "TORX" socket wrench, remove the 2 screws.
        GTY748149Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. except "TORX" Screw:
      1. Remove the 2 screws.
    3. Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.
      GTY772266Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Visor Holder LH
      Remove in this Direction (1)
      Remove in this Direction (2)
    4. Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.
  39. REMOVE VISOR HOLDER LH 
    1. Turn the visor holder LH approximately 45° and pull it out as indicated by the arrows, in the order shown in the illustration.
      GTY602037Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 45°
      Remove in this Direction (1)
      Remove in this Direction (2)
    2. Disengage the 2 claws to remove the visor holder LH.
  40. REMOVE VISOR BRACKET COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  41. REMOVE VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  42. REMOVE VISOR HOLDER RH 

    HINT: 

    Use the same procedure as for the LH side.

  43. REMOVE SUN ROOF OPENING TRIM MOULDING (for Moon Roof) 
    1. Remove the sun roof opening trim moulding.
  44. REMOVE ROOF HEADLINING ASSEMBLY 
    1. for Windshield Glass Side:
      1. w/o Pre-collision System with EC Mirror:
        1. Disconnect the connector.
      2. w/ Pre-collision System:
        1. Disconnect each connector.
    2. for Front Pillar LH Side:
      1. Remove the protective cover.
        GTY755519Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a w/ Pre-collision System or Manual (SOS) Switch
      2. Disconnect each connector.
      3. Using a clip remover, disengage the 4 clamps.
      4. Install the protective cover.
    3. for Front Pillar RH Side:
      1. Remove the protective cover.
        GTY753007Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Guide
        *b Clamp
      2. Remove the bolt.
      3. Disengage the guide to disconnect the connector bracket.
      4. Using a clip remover, disengage the 2 clamps.
      5. Install the protective cover.
    4. for Rear Pillar LH Side:
      1. Disconnect the connector.
        GTY748151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Using a clip remover, disengage the clamp.
    5. for Rear Pillar RH Side:
      1. Disconnect each connector.
        GTY758001Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a w/ Manual (SOS) Switch
      2. Using a clip remover, disengage each clamp.
    6. for Roof Side (for Normal Roof):
      1. Using a clip remover, remove the 2 clips.
        GTY764117Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Remove in this Direction - -
      2. Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

        HINT: 

        Leave the 2 clips installed the vehicle body.

    7. for Roof Side (for Moon Roof):
      1. Disconnect the connector.
        GTY761794Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        Remove in this Direction - -
      2. Using a clip remover, remove the 2 clips.
      3. Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

        HINT: 

        Leave the 2 clips installed the vehicle body.

    8. Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.
      GTY767899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      NOTE:

      Do not damage the roof headlining assembly or vehicle interior.

    9. Remove the 2 clips from the vehicle body as shown in the illustration.
      GTY765902Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
scientia non olet · About LEMON Manuals