Reassembly [09/2019 - 08/2021]: Procedure

INSTALL NO. 1 ROOF WIRE

for Normal Roof:

Apply butyl tape as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	w/ Room Light Assembly	*B	w/ Spot Light Assembly
*a	Marking	-	-
	Butyl Tape	-	-

NOTE:

Securely attach the butyl tape.

Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	w/ Room Light Assembly	*B	w/ Spot Light Assembly
*a	Marking Tape	*b	Adjustment Area

Engage the 4 clamps.
Attach the No. 1 roof wire with the butyl tape.
NOTE:
- Securely attach the No. 1 roof wire.
- If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.
- Make sure to attach the No. 1 roof wire without leaving any of it loose.
HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.

Install the No. 1 roof wire to the roof headlining with adhesive tape.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	w/ Room Light Assembly	*B	w/ Spot Light Assembly
*1	No. 1 Roof Wire	-	-
*a	Correct	*b	Incorrect
*c	10 mm (0.394 in.) or more	-	-
	Adhesive Tape	-	-

ADHESIVE TAPE SIZE

Area	Dimension	Area	Dimension
A	20 mm (0.787 in.)	B	80 mm (3.15 in.) or more

NOTE:

Apply the tape securely in place.
Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

except Normal Roof:

Apply butyl tape as shown in the illustration.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	for Moon Roof	*B	for Panoramic Moon Roof
*a	Marking	-	-
	Butyl Tape	-	-

NOTE:

Securely attach the butyl tape.

Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	for Moon Roof	*B	for Panoramic Moon Roof
*a	Marking Tape	*b	90°
*c	Adjustment Area	-	-
	Rotation Direction	-	-

Engage each clamp.
Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.
Attach the No. 1 roof wire with the butyl tape.
NOTE:
- Securely attach the No. 1 roof wire.
- If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.
- Make sure to attach the No. 1 roof wire without leaving any of it loose.
HINT:

Secure the extra length of the No. 1 roof wire in the adjustment area.

Install the No. 1 roof wire to the roof headlining with adhesive tape.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*A	for Moon Roof	*B	for Panoramic Moon Roof
*1	No. 1 Roof Wire	-	-
*a	Correct	*b	Incorrect
*c	10 mm (0.394 in.) or more	-	-
	Adhesive Tape	-	-

ADHESIVE TAPE SIZE

Area	Dimension	Area	Dimension
A	20 mm (0.787 in.)	B	80 mm (3.15 in.) or more

NOTE:

Apply the tape securely in place.
Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY
Refer to PROCEDURE - Step 2 [06/2017 - 10/2020] , or refer to PROCEDURE - Step 2 [10/2020 - ]

INSTALL NO. 4 ROOF SILENCER

for Normal Roof:

Align the No. 4 roof silencer with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

*A	w/ Room Light Assembly	*B	w/ Spot Light Assembly
*a	Hot-melt Glue	*b	Marking

INSTALL NO. 2 ROOF SILENCER

for Normal Roof:

Align the No. 2 roof silencer with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

Hot-melt Glue

Marking

INSTALL VANITY LIGHT ASSEMBLY (w/ Vanity Light)

HINT:

Use the same procedure for the RH side and LH side.

Engage the claw (B) to install the vanity light assembly.

*1	Bulb Holder
*a	Claw (A)
*b	Claw (B)

Engage the 2 claws (A) to install the bulb holder to the vanity light assembly.