LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Seats - Service Information (1 Of 2) (Except Hybrid) >> FRONT SEAT ASSEMBLY (for TMC Made Manual Seat) >> Removal [03/2017 - 09/2019] >> Procedure

Removal [03/2017 - 09/2019]: Procedure

  1. PRECAUTION 
    NOTE:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Refer to PRECAUTION [03/2017 - 06/2017] , or refer to PRECAUTION [06/2017 - 09/2019]

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    WARNING:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [03/2017 - 06/2017] , or refer to INITIALIZATION [06/2017 - 08/2018] , or refer to INITIALIZATION [08/2018 - 09/2019]

  3. REMOVE FRONT SEAT HEADREST ASSEMBLY 
    1. Remove the front seat headrest assembly from the front seat assembly RH.
  4. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH 
    1. Operate the seat track adjusting handle and move the front seat assembly RH to the rearmost position.
    2. Disengage the 2 claws to remove the front outer seat track bracket cover RH.
      GTY768803Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE FRONT INNER SEAT TRACK BRACKET COVER RH 
    1. Disengage the 2 claws to remove the front inner seat track bracket cover RH.
      GTY741641Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH 
    1. Operate the seat track adjusting handle and move the front seat assembly RH to the foremost position.
    2. Disengage the 2 claws and guide to remove the rear outer seat track bracket cover RH.
      GTY741643Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE REAR INNER SEAT TRACK BRACKET COVER RH 
    1. Disengage the 2 claws and guide to remove the rear inner seat track bracket cover RH.
      GTY741644Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE FRONT SEAT ASSEMBLY RH 
    1. GTY748048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly RH.

    2. Operate the seat track adjusting handle and move the front seat assembly RH to the rearmost position.
    3. GTY748051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly RH.

    4. Operate the vertical adjusting handle and move the front seat assembly RH to the uppermost position.
    5. Operate the seat track adjusting handle and move the front seat assembly RH to the center position.
    6. Operate the reclining adjuster release handle and move the seatback to the upright position.
    7. Disconnect the front seat airbag assembly RH connector under the front seat assembly RH.
      NOTE:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
        GTY544897Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a White Housing Lock
        *b Yellow CPA
        Slide
      2. Push down the white housing lock again and disconnect the connector.
        NOTE:

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    8. Disconnect each connector and disengage each clamp under the front seat assembly RH.
    9. Remove the front seat assembly RH.
      NOTE:

      Be careful not to damage the vehicle body.

      GTY759766Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002