LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Camry TRD >> Repair and Diagnosis >> Accessories & Equipment >> Infotainment >> Navigation System - Diagnostic Codes & Symptom Tests (1 Of 2) (Except Hybrid) >> Navigation System >> DTC B1579: Voice Recognition Microphone Disconnected [06/2017 - 09/2019] >> Procedure

DTC B1579: Voice Recognition Microphone Disconnected [06/2017 - 09/2019]: Procedure

  1. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY 
    1. Measure the resistance according to the value(s) in the table below.
      GTY744943Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Radio and Display Receiver Assembly)

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-22 (MIN-) - Body ground Always Below 1 Ω

      Result

      Result Proceed to
      OK (w/ Sliding Roof and w/o Manual (SOS) Switch) A
      OK (w/ Sliding Roof and w/ Manual (SOS) Switch) B
      OK (w/o Sliding Roof and w/o Manual (SOS) Switch) C
      OK (w/o Sliding Roof and w/ Manual (SOS) Switch) D
      NG E

    Result: 

    B 

    See step  3

    Result: 

    C 

    See step  9

    Result: 

    D 

    See step  10

    Result: 

    E 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020] 

    Result: 

    A 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY) 
    1. Disconnect the K2 radio and display receiver assembly connector.
    2. Disconnect the V14 roof console box sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
      K2-22 (MIN-) - V14-7 (MCO-) Always Below 1 Ω
      K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher
      K2-22 (MIN-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  7

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  3. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY) 
    1. Disconnect the K12 DCM (telematics transceiver) connector.
    2. Disconnect the V14 roof console box sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K12-35 (MCI-) - V14-7 (MCO-) Always Below 1 Ω
      K12-35 (MCI-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  4

  4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER)) 
    1. Disconnect the K2 radio and display receiver assembly connector.
    2. Disconnect the K12 DCM (telematics transceiver) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-22 (MIN-) - K12-19 (MCO-) Always Below 1 Ω
      K2-22 (MIN-) or K12-19 (MCO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  5

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY) 
    1. Disconnect the K2 radio and display receiver assembly connector.
    2. Disconnect the V14 roof console box sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
      K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  6

  6. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Connect the K12 DCM (telematics transceiver) connector.
    2. Connect the K2 radio and display receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.
      GTY744839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      K12-35 (MCI-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [03/2017 - 09/2019] 

    Result: 

    OK 

    See step  7

  7. INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY 
    1. Remove the roof console box sub-assembly.

      Refer to REMOVAL [06/2017 - ]

    2. Connect the B telephone microphone assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      6 (SNS2) - 7 (MCO-) Always Below 1 Ω
      GTY753732Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Roof Console Box Sub-assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020] 

    Result: 

    NG 

    See step  8

  8. INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY 
    1. Remove the roof console box sub-assembly.

      Refer to REMOVAL [06/2017 - ]

    2. Disconnect the B telephone microphone assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B-1 - V14-6 (SNS2) Always Below 1 Ω
      B-2 - V14-7 (MCO-) Always Below 1 Ω
      B-1 or V14-6 (SNS2) - V14-15 (GND) Always 10 kΩ or higher
      B-2 or V14-7 (MCO-) - V14-15 (GND) Always 10 kΩ or higher
      GTY748021Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
      *b Component without harness connected
      (Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TELEPHONE MICROPHONE ASSEMBLY. Refer to  REMOVAL [06/2017 - 09/2019] 

    Result: 

    NG 

    REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY. Refer to  REMOVAL [06/2017 - ] 

  9. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY) 
    1. Disconnect the K2 radio and display receiver assembly connector.
    2. Disconnect the V18 roof console box sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-25 (SNS2) - V18-3 (SNS2) Always Below 1 Ω
      K2-22 (MIN-) - V18-4 (MCO-) Always Below 1 Ω
      K2-25 (SNS2) or V18-3 (SNS2) - Body ground Always 10 kΩ or higher
      K2-22 (MIN-) or V18-4 (MCO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    See step  14

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

  10. CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY) 
    1. Disconnect the K12 DCM (telematics transceiver) connector.
    2. Disconnect the V18 roof console box sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K12-35 (MCI-) - V18-4 (MCO-) Always Below 1 Ω
      K12-35 (MCI-) or V18-4 (MCO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  11

  11. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER)) 
    1. Disconnect the K2 radio and display receiver assembly connector.
    2. Disconnect the K12 DCM (telematics transceiver) connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-22 (MIN-) - K12-19 (MCO-) Always Below 1 Ω
      K2-22 (MIN-) or K12-19 (MCO-) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  12

  12. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY) 
    1. Disconnect the K2 radio and display receiver assembly connector.
    2. Disconnect the V18 roof console box sub-assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      K2-25 (SNS2) - V18-3 (SNS2) Always Below 1 Ω
      K2-25 (SNS2) or V18-3 (SNS2) - Body ground Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  13

  13. INSPECT DCM (TELEMATICS TRANSCEIVER) 
    1. Connect the K12 DCM (telematics transceiver) connector.
    2. Connect the K2 radio and display receiver assembly connector.
    3. Measure the resistance according to the value(s) in the table below.
      GTY744839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (DCM (Telematics Transceiver))

      Standard Resistance

      Tester Connection Condition Specified Condition
      K12-35 (MCI-) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPLACE DCM (TELEMATICS TRANSCEIVER). Refer to  REMOVAL [03/2017 - 09/2019] 

    Result: 

    OK 

    See step  14

  14. INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY 
    1. Remove the roof console box sub-assembly.

      Refer to REMOVAL [06/2017 - ]

    2. Connect the B telephone microphone assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      3 (SNS2) - 4 (MCO-) Always Below 1 Ω
      GTY756998Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Roof Console Box Sub-assembly)

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY. Refer to  REMOVAL [06/2017 - 10/2020] 

    Result: 

    NG 

    See step  15

  15. INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY 
    1. Remove the roof console box sub-assembly.

      Refer to REMOVAL [06/2017 - ]

    2. Disconnect the B telephone microphone assembly connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B-1 - V18-3 (SNS2) Always Below 1 Ω
      B-2 - V18-4 (MCO-) Always Below 1 Ω
      B-1 or V18-3 (SNS2) - V18-11 (GND) Always 10 kΩ or higher
      B-2 or V18-4 (MCO-) - V18-11 (GND) Always 10 kΩ or higher
      GTY767801Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component without harness connected
      (Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
      *b Component without harness connected
      (Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE TELEPHONE MICROPHONE ASSEMBLY. Refer to  REMOVAL [06/2017 - 09/2019] 

    Result: 

    NG 

    REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY. Refer to  REMOVAL [06/2017 - ] 

scientia non olet · About LEMON Manuals